| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
MP8761GL bảng dữ liệu(PDF) 15 Page - Monolithic Power Systems |
|
|
|||||||||||||||||||||||||||||
MP8761GL bảng dữ liệu(HTML) 15 Page - Monolithic Power Systems |
|
15 / 24 page ![]() MP8761 — 8A, 18V, SYNCHRONOUS STEP-DOWN CONVERTER MP8761 Rev. 1.1 www.MonolithicPower.com 15 11/4/2013 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2013 MPS. All Rights Reserved. case, 6V) for the internal zener clamp should be less than 1mA. Therefore, when driving EN with an external logic signal, use an EN voltage less than 6V; when connecting EN to IN through a pull-up resistor or a resistive voltage divider, select a resistance that ensures a maximum pull up current less than 1mA. If using a resistive voltage divider and VIN exceeds 6V, then the minimum resistance for the pull-up resistor RUP should meet: IN UP DOWN V6V 6V 1mA RR − −≤ (12) With only RUP (the pull-down resistor RDOWN is not connected), then the VCC UVLO threshold determines VIN-START so the minimum resistor value is: IN UP V6V R( ) 1mA − ≥Ω (13) A typical pull-up resistor is 100kΩ. Soft-Start The MP8761 employs soft-start (SS) to ensure a smooth output during power-up. When the EN pin goes HIGH, an internal current source (20μA) charges the SS capacitor. The SS capacitor voltage takes over the REF voltage to the PWM comparator. The output voltage smoothly ramps up with the SS voltage. It continues ramping up while VREF takes over the PWM comparator. At this point, soft-start finishes and the device enters steady state operation. Determine the SS capacitor value as follows: () () ( ) () ×μ = SS SS SS REF Tms I A CnF VV (14) If the output capacitors are large, then avoid setting a short SS time or risk hitting the current limit during SS. Use a minimum value of 4.7nF if the output capacitance value exceeds 330μF. Pre-Bias Startup The MP8761 is designed for monotonic startup for pre-biased loads. If the output is pre-biased to a certain voltage during startup, the IC will disable switching for both high-side and low-side switches until the voltage on the soft-start capacitor exceeds the sensed output voltage at the FB pin. Power Good (PG) The MP8761 has a power-good (PG) output. The PG pin is the open drain of a MOSFET. Connect it to VCC or some other voltage source that measures less than 5.5V through a pull-up resistor (typically 100kΩ). After applying the input voltage, the MOSFET turns ON so that the PG pin is pulled to GND before the SS is ready. After the FB voltage reaches 91% of the REF voltage, the PG pin is pulled HIGH after a 2.5ms delay. When the FB voltage drops to 80% of the REF voltage or exceeds 120% of the nominal REF voltage, the PG pin is pulled LOW. If the input supply fails to power the MP8761, the PG pin is also pulled low even though this pin is tied to an external DC source through a pull-up resistor (typically. 100kΩ). Over-Current Protection (OCP) The MP8761 features two current limit levels for over-current conditions: low-side valley current limit and low-side negative current limit. Low-Side Valley Current Limit: The device monitors the inductor current during LS-FET ON state. At the end of OFF time, the LS-FET sourcing current is compared to the internal positive-valley-current limit. If the valley current limit is less than LS-FET sourcing current, the LS-FET turns OFF and the HS- FET turns ON for a fixed time determined by frequency-set resistor RFREQ and input voltage. During OCP, the device tries to recover from the over-current fault with hiccup mode: the chip disables the output power stage, discharges the soft-start capacitor and then automatically retries soft-start. If the over- current condition still holds after soft-start ends, the device repeats this operation cycle until the over-current conditions disappear and then output rises back to regulation level. OCP offers non-latch protection. Low-Side Negative Current Limit: If the sensed LS-FET negative current exceeds the |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |