AD607ARS datasheet(18/24 Pages) AD

18 / 24 page

REV. C

–18–

AD607

Bias System

The AD607 operates from a single supply, VP, usually of 3 V, at

a typical supply current of 8.5 mA at midgain and T = 27

°C,

corresponding to a power consumption of 25 mW. Any voltage

from 2.92 V to 5.5 V may be used.

The bias system includes a fast-acting active-high CMOS-

compatible power-up switch, allowing the part to idle at 550

µA

when disabled. Biasing is proportional-to-absolute temperature

(PTAT) to ensure stable gain with temperature.

An independent regulator generates a voltage at the midpoint

of the supply (VP/2) that appears at the VMID pin at a low

impedance. This voltage does not shut down, ensuring that the

major signal interfaces (e.g., mixer-to-IF and IF-to-demodulators)

remain biased at all times, thus minimizing transient disturbances

at power-up and allowing the use of substantial decoupling

capacitors on this node. The quiescent consumption of this

regulator is included in the idling current.

AD607

FDIN

50k

VPOS

EXTERNAL

FREQUENCY

REFERENCE

a. Biasing FDIN from Supply when Using

External Frequency Reference

AD607

FDIN

50k

CBYPASS

EXTERNAL

FREQUENCY

REFERENCE

VMID

b. Biasing FDIN from VMID when Using

External Frequency Reference

Figure 21. Suggested Methods for Biasing Pin FDIN at VP/2

USING THE AD607

In this section, we will focus on a few areas of special impor-

tance and include a few general application tips. As is true of

any wideband high gain component, great care is needed in PC

board layout. The location of the particular grounding points

must be considered with due regard to the possibility of unwanted

signal coupling, particularly from IFOP to RFHI or IFHI or both.

The high sensitivity of the AD607 leads to the possibility that

unwanted local EM signals may have an effect on the perfor-

mance. During system development, carefully-shielded test

assemblies should be used. The best solution is to use a fully-

enclosed box enclosing all components, with the minimum

number of needed signal connectors (RF, LO, I, and Q outputs)

in miniature coax form.

The I and Q output leads can include small series resistors

(about 100

Ω) inside the shielded box without significant loss

of performance, provided the external loading during testing

is light (that is, a resistive load of more than 20 k

Ω and capaci-

tances of a few picofarads). These help to keep unwanted RF

emanations out of the interior.

The power supply should be connected via a through-hole

capacitor with a ferrite bead on both inside and outside leads.

Close to the IC pins, two capacitors of different value should be

used to decouple the main supply (VP) and the midpoint supply

pin, VMID. Guidance on these matters is also generally included

in applications schematics.

Gain Distribution

As in all receivers, the most critical decisions in effectively using

the AD607 relate to the partitioning of gain between the various

subsections (Mixer, IF Amplifier, Demodulators) and the place-

ment of filters so as to achieve the highest overall signal-to-noise

ratio and lowest intermodulation distortion.

Figure 22 shows the main RF/IF signal path at maximum and

minimum signal levels.

IOUT

QOUT

RFHI

LOIP

MXOP

IFHI

DMIP

IFOP

IF BPF

(VMID)

330

(TYPICAL

IMPEDANCE)

(LOCATION OF OPTIONAL

SECOND IF FILTER)

CONSTANT

–16dBm

( 50mV)

54mV

MAX INPUT

1.3V

MAX OUTPUT

54mV

MAX INPUT

560mV

MAX OUTPUT

154mV

MAX INPUT

1.23V

MAX OUTPUT

Figure 22. Signal Levels for Minimum and Maximum Gain

AD607ARS bảng dữ liệu(PDF) 18 Page - Analog Devices

AD607ARS bảng dữ liệu(HTML) 18 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24

bảng dữ liệu tải về

Link URL