PIC18F2610ESLASHSPQTP datasheet(98/376 Pages) MICROCHIP

98 / 376 page

PIC18F2X1X/4X1X

DS39636D-page 100

9.2

PORTB, TRISB and LATB

Registers

PORTB is an 8-bit wide, bidirectional port. The

corresponding data direction register is TRISB. Setting

a TRISB bit (= 1) will make the corresponding PORTB

pin an input (i.e., put the corresponding output driver in

a high-impedance mode). Clearing a TRISB bit (= 0)

will make the corresponding PORTB pin an output (i.e.,

put the contents of the output latch on the selected pin).

The Data Latch register (LATB) is also memory

mapped. Read-modify-write operations on the LATB

PORTB.

EXAMPLE 9-2:

INITIALIZING PORTB

Each of the PORTB pins has a weak internal pull-up. A

single control bit can turn on all the pull-ups. This is

performed by clearing bit, RBPU (INTCON2<7>). The

weak pull-up is automatically turned off when the port

pin is configured as an output. The pull-ups are

disabled on a Power-on Reset.

Four of the PORTB pins (RB7:RB4) have an interrupt-

on-change feature. Only pins configured as inputs can

cause this interrupt to occur (i.e., any RB7:RB4 pin

configured as an output is excluded from the interrupt-

on-change comparison). The input pins (of RB7:RB4)

are compared with the old value latched on the last

read of PORTB. The “mismatch” outputs of RB7:RB4

are ORed together to generate the RB Port Change

Interrupt with Flag bit, RBIF (INTCON<0>).

This interrupt can wake the device from the Sleep

mode, or any of the Idle modes. The user, in the

Interrupt Service Routine, can clear the interrupt in the

following manner:

a) Any read or write of PORTB (except with the

MOVFF (ANY), PORTB instruction).

b) Clear flag bit RBIF.

A mismatch condition will continue to set flag bit RBIF.

Reading PORTB will end the mismatch condition and

allow flag bit RBIF to be cleared.

The interrupt-on-change feature is recommended for

wake-up on key depression operation and operations

where PORTB is only used for the interrupt-on-change

feature. Polling of PORTB is not recommended while

using the interrupt-on-change feature.

RB3 can be configured by the Configuration bit,

CCP2MX, as the alternate peripheral pin for the CCP2

module (CCP2MX = 0).

Note:

On a Power-on Reset, RB4:RB0 are

configured as analog inputs by default and

read as ‘0’; RB7:RB5 are configured as

digital inputs.

By programming the Configuration bit,

PBADEN, RB4:RB0 will alternatively be

configured as digital inputs on POR.

CLRF

PORTB

; Initialize PORTB by

; clearing output

; data latches

CLRF

LATB

; Alternate method

; to clear output

; data latches

MOVLW

0Fh

; Set RB<4:0> as

MOVWF

ADCON1 ; digital I/O pins

; (required if config bit

; PBADEN is set)

MOVLW

0CFh

; Value used to

; initialize data

; direction

MOVWF

TRISB

; Set RB<3:0> as inputs

; RB<5:4> as outputs

; RB<7:6> as inputs

PIC18F2610E/SPQTP bảng dữ liệu(PDF) 98 Page - Microchip Technology

PIC18F2610E/SPQTP bảng dữ liệu(HTML) 98 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL