PIC18F1220ESLASHSSSQTP datasheet(246/308 Pages) MICROCHIP

246 / 308 page

PIC18F1220/1320

DS39605F-page 244

Supply Current (IDD)(2,3)

PIC18LF1220/1320

140

275

μA

-40°C

FOSC = 4 MHz

(RC_IDLE mode,

Internal oscillator source)

140

275

μA+25°C

VDD = 2.0V

150

275

μA+85°C

PIC18LF1220/1320

220

375

μA

-40°C

220

375

μA+25°C

VDD = 3.0V

220

375

μA+85°C

All devices

390

800

μA

-40°C

VDD = 5.0V

400

800

μA+25°C

380

800

μA+85°C

Extended devices

410

800

μA

+125°C

PIC18LF1220/1320

150

250

μA

-40°C

FOSC = 1 MHZ

(PRI_RUN mode,

EC oscillator)

150

250

μA+25°C

VDD = 2.0V

160

250

μA+85°C

PIC18LF1220/1320

340

350

μA

-40°C

300

350

μA+25°C

VDD = 3.0V

280

350

μA+85°C

All devices

0.72

1.0

-40°C

VDD = 5.0V

0.63

1.0

+25°C

0.58

1.0

+85°C

Extended devices

0.53

1.0

+125°C

22.2

DC Characteristics: Power-Down and Supply Current

PIC18F1220/1320 (Industrial)

PIC18LF1220/1320 (Industrial) (Continued)

PIC18LF1220/1320

(Industrial)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

≤ TA ≤ +85°C for industrial

PIC18F1220/1320

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

≤ TA ≤ +85°C for industrial

-40°C

≤ TA ≤ +125°C for extended

Param

No.

Device

Typ

Max

Units

Conditions

Legend:

Shading of rows is to assist in readability of the table.

Note

The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in k

Ω.

Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended temperature

crystals are available at a much higher cost.

PIC18F1220E/SSSQTP bảng dữ liệu(PDF) 246 Page - Microchip Technology

PIC18F1220E/SSSQTP bảng dữ liệu(HTML) 246 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL