| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F1220E/SOSQTP bảng dữ liệu(PDF) 177 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F1220E/SOSQTP bảng dữ liệu(HTML) 177 Page - Microchip Technology |
|
177 / 308 page ![]() © 2007 Microchip Technology Inc. DS39605F-page 175 PIC18F1220/1320 REGISTER 19-4: CONFIG3H: CONFIGURATION REGISTER 3 HIGH (BYTE ADDRESS 300005h) REGISTER 19-5: CONFIG4L: CONFIGURATION REGISTER 4 LOW (BYTE ADDRESS 300006h) R/P-1 U-0 U-0 U-0 U-0 U-0 U-0 U-0 MCLRE — — — — — — — bit 7 bit 0 bit 7 MCLRE: MCLR Pin Enable bit 1 =MCLR pin enabled, RA5 input pin disabled 0 = RA5 input pin enabled, MCLR disabled bit 6-0 Unimplemented: Read as ‘0’ Legend: R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’ -n = Value when device is unprogrammed u = Unchanged from programmed state R/P-1 U-0 U-0 U-0 U-0 R/P-1 U-0 R/P-1 DEBUG — — — —LVP —STVR bit 7 bit 0 bit 7 DEBUG: Background Debugger Enable bit (see note) 1 = Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins 0 = Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug bit 6-3 Unimplemented: Read as ‘0’ bit 2 LVP: Low-Voltage ICSP Enable bit 1 = Low-Voltage ICSP enabled 0 = Low-Voltage ICSP disabled bit 1 Unimplemented: Read as ‘0’ bit 0 STVR: Stack Full/Underflow Reset Enable bit 1 = Stack full/underflow will cause Reset 0 = Stack full/underflow will not cause Reset Legend: R = Readable bit C = Clearable bit U = Unimplemented bit, read as ‘0’ -n = Value when device is unprogrammed u = Unchanged from programmed state Note: The Timer1 oscillator shares the T1OSI and T1OSO pins with the PGD and PGC pins used for programming and debugging. When using the Timer1 oscillator, In-Circuit Serial Programming (ICSP) may not function correctly (high voltage or low voltage), or the In-Circuit Debugger (ICD) may not communicate with the controller. As a result of using either ICSP or ICD, the Timer1 crystal may be damaged. If ICSP or ICD operations are required, the crystal should be disconnected from the circuit (disconnect either lead) or installed after programming. The oscillator loading capacitors may remain in-circuit during ICSP or ICD operation. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |