LMP2234AMASLASHNOPB datasheet(5/31 Pages) TI

5 / 31 page

LMP2234

www.ti.com

SNOSAW4D – SEPTEMBER 2007 – REVISED MARCH 2013

3.3V DC Electrical Characteristics

(1) (continued)

Unless otherwise specified, all limits are ensured for TA = 25°C, V

+ = 3.3V, V− = 0V, V

CM = VO = V

+/2, and R

L > 1 MΩ.

Boldface limits apply at the temperature extremes.

Symbol

Parameter

Conditions

Min

Typ

Max

Units

(2)

(3)

(2)

Output Current

Sourcing, VO to V

−

(4)

VIN(diff) = 100 mV

Sinking, VO to V

VIN(diff) = −100 mV

Supply Current

µA

(4)

The short circuit test is a momentary open loop test.

3.3V AC Electrical Characteristics

(1)

Unless otherwise is specified, all limits are ensured for TA = 25°C, V

+ = 3.3V, V− = 0V, V

CM = VO = V

+/2, and R

L > 1 MΩ.

Boldface limits apply at the temperature extremes.

Symbol

Parameter

Conditions

Min

Typ

Max

Units

(2)

(3)

(2)

GBWP

Gain Bandwidth Product

CL = 20 pF, RL = 10 kΩ

128

kHz

Slew Rate

AV = +1, CL = 20 pF

Falling Edge

V/ms

RL = 10 kΩ

Rising Edge

θ m

Phase Margin

CL = 20 pF, RL = 10 kΩ

deg

Gain Margin

CL = 20 pF, RL = 10 kΩ

Input-Referred Voltage Noise Density

f = 1 kHz

nV/

√Hz

Input-Referred Voltage Noise

0.1 Hz to 10 Hz

2.4

μVPP

Input-Referred Current Noise Density

f = 1 kHz

fA/

√Hz

THD+N

Total Harmonic Distortion + Noise

f = 100 Hz, RL = 10 kΩ

0.003

(1)

Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very

limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical

tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond

which the device may be permanently degraded, either mechanically or electrically.

(2)

All limits are specified by testing, statistical analysis or design.

(3)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

2.5V DC Electrical Characteristics

(1)

Unless otherwise specified, all limits are ensured for TA = 25°C, V

+ = 2.5V, V− = 0V, V

CM = VO = V

+/2, and R

L > 1MΩ.

Boldface limits apply at the temperature extremes.

Symbol

Parameter

Conditions

Min

Typ

Max

Units

(2)

(3)

(2)

VOS

Input Offset Voltage

±10

±190

μV

±275

TCVOS

Input Offset Voltage Drift

LMP2234A

±0.3

±0.75

μV/°C

LMP2234B

±0.3

±2.5

IBIAS

Input Bias Current

±0.02

±1.0

±50

IOS

Input Offset Current

±5

(1)

Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very

limited self-heating of the device such that TJ = TA. No ensured specification of parametric performance is indicated in the electrical

tables under conditions of internal self-heating where TJ > TA. Absolute Maximum Ratings indicate junction temperature limits beyond

which the device may be permanently degraded, either mechanically or electrically.

(2)

All limits are specified by testing, statistical analysis or design.

(3)

Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary

over time and will also depend on the application and configuration. The typical values are not tested and are not ensured on shipped

production material.

Submit Documentation Feedback

Product Folder Links: LMP2234

LMP2234AMA/NOPB bảng dữ liệu(PDF) 5 Page - Texas Instruments

LMP2234AMA/NOPB bảng dữ liệu(HTML) 5 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31

bảng dữ liệu tải về

Link URL