| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
HT85F2270 bảng dữ liệu(PDF) 202 Page - Holtek Semiconductor Inc |
|
|
|||||||||||||||||||||||||||||
HT85F2270 bảng dữ liệu(HTML) 202 Page - Holtek Semiconductor Inc |
|
202 / 226 page ![]() Rev. 1.00 �0� of ��6 �a� 1�� �01� Standard 8051 8-Bit Flash MCU HT85F2260/HT85F2270/HT85F2280 S0CON Register – UART0 Control register SFR Address: 98h Bit 7 6 5 4 3 2 1 0 Name S�0 S�1 S��0 REN0 TB80 RB80 TI0 RI0 R/W R/W R/W R/W R/W R/W R/W R/W R/W POR 0 0 0 0 0 0 0 0 Bit 7~6 SM0, SM1: UART0 Operating mode select bits 00: Mode 0 01: Mode 1 10: Mode 2 11: Mode 3 The following table illustrates the corresponding mode descriptions and baud rates. In mode1 and mode 3, the variable baud rate is dependent on the system clock, the baud rate clock source and the prescaler selections. Operating mode details are described elsewhere. Mode Mode Name Baud Rate Synchronisation �ode 0 8-bit shift register fSYS/1� S�nchronous �ode 1 8-bit UART Variable As�nchronous �ode � 9-bit UART SP0CLK/�� or SP0CLK/64 As�nchronous �ode � 9-bit UART Variable As�nchronous Note that the SP0CLK is described in the UART0 Baud Rate Setup section. Bit 5 SM20: Multiprocessor communication enable control 0: Disable 1: Enable Refer to the UART0 Multiprocessor Communication section for details. Bit 4 REN0: UART0 serial data reception enable control 0: Disable 1: Enable Bit 3 TB80: Ninth Transmit bit assignment 0: Low 1: High This bit is only available in Mode 2 and Mode 3. It is not effective in Mode 0 and Mode 1. The bit is assigned using the application program. Bit 2 RB80: Ninth Receive bit assignment 0: Low 1: High This bit is used to assign the level of the ninth bit in Mode 2 and Mode 3. In mode 1, if the SM20 bit is zero, the RB80 bit is assigned as the level of the received stop bit. It is not available in Mode 0. Bit 1 TI0: UART0 transmit interrupt flag 0: No interrupt request 1: Interrupt request This bit must be cleared using the application program. Bit 0 RI0: UART0 receive interrupt flag 0: No interrupt request 1: Interrupt request This bit must be cleared using the application program. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |