18F45K80 datasheet(13/52 Pages) MICROCHIP

13 / 52 page

 2011 Microchip Technology Inc.

DS39972B-page 13

PIC18FXXK80 FAMILY

FIGURE 2-12:

EXITING LOW-VOLTAGE

PROGRAM/VERIFY MODE

FIGURE 2-13:

EXITING HIGH-VOLTAGE

PROGRAM/VERIFY MODE

2.7

Entering and Exiting Low-Voltage

ICSP Program/Verify Mode

As shown in Figure 2-10, entering Low-Voltage ICSP

Program/Verify mode requires three steps:

The MCLR pin is grounded.

A 32-bit key sequence is presented on PGD.

The MCLR pin is brought to VDD

The MCLR pin must be grounded during the transfer of

the key sequence. After MCLR is grounded, an interval

of at least P12 must elapse before presenting the key

sequence on PGD. The key sequence is a specific

32-bit pattern,‘0100 1101 0100 0011 0100 1000

0101 0000

’ (more easily remembered as 4D434850h

in hexadecimal). The device will enter Program/Verify

mode only if the sequence is valid. The Most Significant

bit of the most significant nibble must be shifted in first.

Once the key sequence is complete, VIH, or usually

VDD, must be applied to MCLR and held at that level for

as long as Program/Verify mode is to be maintained.

There is no minimum time requirement before present-

ing data on PGD. On successful entry, the program

memory can be accessed and programmed in serial

fashion. While in the Program/Verify mode, all unused

I/Os are placed in the high-impedance state.

Exiting Program/Verify mode is done by grounding the

MCLR again, as shown in Figure 2-12. The only

requirement for exit is that an interval, P16, should

elapse between the last clock, and the program signals

on PGC and PGD before grounding MCLR.

2.8

Serial Program/Verify Operation

The PGC pin is used as a clock input pin, and the PGD

pin is used for entering command bits and data input/

output during serial operation. Commands and data are

transmitted on the rising edge of PGC, latched on the

falling edge of PGC, and are Least Significant bit (LSb)

first.

2.8.1

4-BIT COMMANDS

All instructions are 20 bits, consisting of a leading 4-bit

command, followed by a 16-bit operand, which

depends on the type of command being executed. To

input a command, PGC is cycled four times. The com-

mands needed for programming and verification are

shown in Table 2-3. Commands and data are entered

LSb first.

Depending on the 4-bit command, the 16-bit operand

represents 16 bits of input data, or 8 bits of input data

and 8 bits of output data.

Throughout this specification, commands and data are

presented as illustrated in Table 2-4. The 4-bit command

and data are shown Most Significant bit (MSb) first. The

command operand, or “Data Payload”, is shown as

<LSB><MSB>. Figure 2-14 demonstrates how to serially

present a 20-bit command/operand to the device.

MCLR/VPP/RE3

P16

PGD

PGD = Input

PGC

VDD

D041

P17

MCLR/VPP/RE3

P16

PGD

PGD = Input

PGC

VDD

D110

P17

18F45K80 bảng dữ liệu(PDF) 13 Page - Microchip Technology

18F45K80 bảng dữ liệu(HTML) 13 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

bảng dữ liệu tải về

Link URL