MCP98244 datasheet(17/52 Pages) MICROCHIP

17 / 52 page

 2012-2013 Microchip Technology Inc.

DS22327C-page 17

MCP98244

bit 7

TCRIT Lock Bit (Crit. Lock):

Unlocked. TCRIT register can be written (power-up default)

=Locked. TCRIT register can not be written

When enabled, this bit remains set ‘1’ or locked until cleared by internal reset (Section 5.4 “Summary

of Power-On Default”

). This bit does not require a double-write.

This bit can be programmed in Shutdown mode.

bit 6

TUPPER and TLOWER Window Lock Bit (Win. Lock):

Unlocked. TUPPER and TLOWER registers can be written (power-up default)

=Locked. TUPPER and TLOWER registers can not be written

When enabled, this bit remains set ‘1’ or locked until cleared by power-on Respell (Section 5.4 “Sum-

mary of Power-On Default”

). This bit does not require a double-write.

This bit can be programmed in Shutdown mode.

bit 5

Interrupt Clear (Int. Clear) Bit:

No effect (power-up default)

Clear interrupt output. When read this bit returns ‘0’

This bit clears the Interrupt flag which deasserts Event output. In shutdown mode, the Event output is

always deasserted. Therefore, setting this bit in Shutdown mode clears the interrupt after the device

returns to normal operation.

bit 4

Event Output Status (Event Stat.) Bit:

Event output is not asserted by the device (power-up default)

Event output is asserted as a comparator/Interrupt or critical temperature output

In shutdown mode this bit will clear because Event output is always deasserted in Shutdown mode.

bit 3

Event Output Control (Event Cnt.) Bit:

Event output Disabled (power-up default)

Event output Enabled

This bit can not be altered when either of the lock bits is set (bit 6 and bit 7).

This bit can be programmed in Shutdown mode, but Event output will remain deasserted.

bit 2

Event Output Select (Event Sel.) Bit:

Event output for TUPPER, TLOWER and TCRIT (power-up default)

= TA ≥ TCRIT only. (TUPPER and TLOWER temperature boundaries are disabled.)

When the Alarm Window Lock bit is set, this bit cannot be altered until unlocked (bit 6).

This bit can be programmed in Shutdown mode, but Event output will remain deasserted.

bit 1

Event Output Polarity (Event Pol.) Bit:

Active low (power-up default. Pull-up resistor required)

Active-high

This bit cannot be altered when either of the lock bits is set (bit 6 and bit 7).

This bit can be programmed in Shutdown mode, but Event output will remain deasserted, see

Section 5.2.3 “Event Output Configuration”

bit 0

Event Output Mode (Event Mod.) Bit:

Comparator output (power-up default)

Interrupt output

This bit cannot be altered when either of the lock bits is set (bit 6 and bit 7).

This bit can be programmed in Shutdown mode, but Event output will remain deasserted.

CONFIGURATION REGISTER (CONFIG)

 ADDRESS ‘0000 0001’b

(CONTINUED)

MCP98244 bảng dữ liệu(PDF) 17 Page - Microchip Technology

MCP98244 bảng dữ liệu(HTML) 17 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52

bảng dữ liệu tải về

Link URL