AD9901TESLASH883 datasheet(2/8 Pages) AD

2 / 8 page

REV. B

–2–

AD9901–SPECIFICATIONS

ABSOLUTE MAXIMUM RATINGS

Positive Supply Voltage (+VS for TTL Operation) . . . . . +7 V

Negative Supply Voltage (–VS for ECL Operation) . . . . . –7 V

Input Voltage Range (TTL Operation) . . . . . . . 0 V to +5.5 V

Differential Input Voltage (ECL Operation) . . . . . . . . . . 4.0 V

ISET Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 mA

Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mA

ELECTRICAL CHARACTERISTICS

Commercial Temperature

0 C to +70 C

AD9901KQ/KP

Test

Temp

Level

Min

Typ

Max

Units

INPUT CHARACTERISTICS

TTL Input Logic “1” Voltage

Full

2.0

TTL Input Logic “0” Voltage

Full

0.8

TTL Input Logic “1” Current

Full

0.6

TTL Input Logic “0” Current

Full

1.6

ECL Differential Switching Voltage

Full

300

ECL Input Current

Full

µA

OUTPUT CHARACTERISTICS

Peak-to-Peak Output Voltage Swing

Full

1.6

1.8

2.0

TTL Output Compliance Range

Full

3–7

ECL Output Compliance Range

Full

±2V

IOUT Range

Full

0.9–11

Internal Reference Voltage

Full

0.42

0.47

0.52

AC CHARACTERISTICS

Linear Phase Detection Range4

40 kHz

+25

°C

360

Degrees

30 MHz

+25

°C

320

Degrees

70 MHz

+25

°C

270

Degrees

Functionality @ 70 MHz

+25

°C

Pass/Fail

POWER SUPPLY CHARACTERISTICS

TTL Supply Current (+5.0 V)5, 6

+25

°C

43.5

54.0

Full

43.5

54.0

ECL Supply Current (–5.2 V)5, 6

+25

°C

42.5

52.5

Full

42.5

52.5

Nominal Power Dissipation

+25

°C

218

NOTES

1Absolute maximum ratings are limiting values, to be applied individually, and beyond which the service ability of the circuit may be impaired. Functional operability

is not necessarily implied. Exposure to absolute maximum rating conditions for an extended period of time may affect device reliability.

2Maximum junction temperature should not exceed +175

°C for ceramic packages, +150°C for plastic packages. Junction temperature can be calculated by:

tJ = PD (θJA) +tA = PD (θJC) +tC

where:

PD = power dissipation

JA = thermal impedance from junction to air (°C/W)

JC = thermal impedance from junction to case ( °C/W)

tA = ambient temperature (°C)

tC = case temperature (°C)

typical thermal impedances:

AD9901 Ceramic DIP =

JA = 74°C/W; θJC = 21°C/W

AD9901 LCC =

JA = 80°C/W; θJC = 19°C/W

AD9901 PLCC =

JA = 88.2°C/W; θJC = 45.2°C/W

L = +0.4 V; VH = +2.4 V.

SET = 47.5 Ω; R L = 182 Ω.

5lncludes load current of 10 mA (load resistors = 182

Ω).

6Supply should remain stable within

± 5% for normal operation.

Specifications subject to change without notice.

Operating Temperature Range

AD9901KQ/KP . . . . . . . . . . . . . . . . . . . . . . . 0

°C to +70°C

Storage Temperature Range . . . . . . . . . . . . –65

°C to +150°C

Junction Temperature

Plastic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+150

°C

Ceramic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+175

°C

Lead Soldering Temperature (10 sec) . . . . . . . . . . . . . +300

°C

( VS = +5.0 V [for TTL] or –5.2 V [for ECL], unless otherwise noted)

AD9901TE/883 bảng dữ liệu(PDF) 2 Page - Analog Devices

AD9901TE/883 bảng dữ liệu(HTML) 2 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8

bảng dữ liệu tải về

Link URL