AD8015 datasheet(2/8 Pages) AD

2 / 8 page

AD8015–SPECIFICATIONS

REV. A

–2–

(SO Package @ TA = +25 C and VS = +5 V, unless otherwise noted)

AD8015AR

Parameter

Conditions

Min

Typ

Max

Units

DYNAMIC PERFORMANCE

Bandwidth

3 dB

180

240

MHz

Pulse Width Modulation

µA to 200 µA Peak

500

Rise and Fall Time

10% to 90%

1.5

Settling Time

to 3%, 0.5 V Diff Output Step

INPUT

Linear Input Current Range

±2.5%, Nonlinearity

±25

±30

µA

Max Input Current Range

Saturation

±200

±350

µA

Optical Sensitivity

155 Mbps, Avg Power

–36

dBm

Input Stray Capacitance

Die, by Design

0.2

SOIC, by Design

0.4

Input Bias Voltage

+VS to IIN and VBYP

1.6

1.8

2.0

NOISE

Die, Single Ended at POUT,

or Differential (POUT–NOUT),

CSTRAY = 0.3 pF

Input Current Noise

f = 100 MHz

3.0

pA/

√Hz

Total Input RMS Noise

DC to 100 MHz

26.5

TRANSFER CHARACTERISTICS

Transresistance

Single Ended

Ω

Differential

Ω

Power Supply

Single Ended

37.0

Rejection Ratio

Differential

OUTPUT

Differential Offset

620

Output Common-Mode Voltage

From Positive Supply

–1.5

–1.3

–1.1

Voltage Swing (Differential)

Positive Input Current, RL =

∞

1.0

V p-p

Positive Input Current, RL = 50 Ω

600

mV p-p

Output Impedance

Ω

POWER SUPPLY

TMIN to TMAX

Operating Range

Single Supply

+4.5

+11

Dual Supply

±2.25

±5.5

Current

NOTES

1Settling Time is defined as the time elapsed from the application of a perfect step input to the time when the output has entered and remained within a specified error

band symmetrical about the final value. This parameter includes propagation delay, slew time, overload recovery, and linear settling times.

Specifications subject to change without notice.

WARNING!

ESD SENSITIVE DEVICE

CAUTION

ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily

accumulate on the human body and test equipment and can discharge without detection.

Although the AD8015 features proprietary ESD protection circuitry, permanent damage may

occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD

precautions are recommended to avoid performance degradation or loss of functionality.

ABSOLUTE MAXIMUM RATINGS

Supply Voltage (+VS to –VS). . . . . . . . . . . . . . . . . . . . . . . 12 V

Internal Power Dissipation

Small Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.9 Watts

Output Short Circuit Duration . . . . . . . . . . . . . . . Indefinite

Maximum Input Current . . . . . . . . . . . . . . . . . . . . . . . . 10 mA

Storage Temperature Range . . . . . . . . . . . . –65

°C to +125°C

Operating Temperature Range (TMIN to TMAX)

AD8015ACHIP/AR . . . . . . . . . . . . . . . . . . –40

°C to +85°C

Maximum Junction Temperature . . . . . . . . . . . . . . . . . +165

°C

Lead Temperature Range (Soldering 10 sec) . . . . . . . . +300

°C

NOTES

1Stresses above those listed under “Absolute Maximum Ratings” may cause

permanent damage to the device. This is a stress rating only and functional

operation of the device at these or any other conditions above those indicated in the

operational section of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect device reliability.

2Specification is for device in free air: 8-pin SOIC package:

JA = 155

°C/W.

ORDERING GUIDE

Temperature

Package

Model

Range

Description

Option

AD8015AR

–40

°C to +85°C 8-Pin Plastic SOIC SO-8

AD8015ACHIPS –40

°C to +85°C Die Form

AD8015 bảng dữ liệu(PDF) 2 Page - Analog Devices

AD8015 bảng dữ liệu(HTML) 2 Page - Analog Devices

Html Pages

1 2 3 4 5 6 7 8

bảng dữ liệu tải về

Link URL