MPRV datasheet(2/8 Pages) MERITEK

2 / 8 page

Electrical Characteristics (23ºC)

Resistance Tolerance

Hold

Current

Trip

Current

Max.Time

to Trip

Maximum

Current

Rated

Voltage

Typical

Power

Rmin

R1max.

Part

Number

IH, A

IT, A

at 5XIH, Sec

Imax, A

Vmax, V

Pd, W

ohms

MPRV120V010

0.10

0.20

10.0

2.0

120

0.84

3.00

7.50

MPRV120V017

0.17

0.34

10.0

2.0

120

0.84

2.00

7.00

MPRV120V020

0.20

0.40

9.0

2.0

120

1.08

1.83

4.40

MPRV120V025

0.25

0.50

7.5

3.0

120

1.08

1.25

3.00

MPRV120V030

0.30

0.60

8.5

3.0

120

1.44

0.88

2.10

MPRV120V040

0.40

0.80

6.5

3.0

120

1.44

0.55

1.29

MPRV120V050

0.50

1.00

6.0

3.0

120

1.56

0.50

1.17

MPRV120V065

0.65

1.30

5.7

5.0

120

1.68

0.31

0.72

MPRV120V070

0.75

1.50

6.3

5.0

120

1.80

0.25

0.60

MPRV120V075

0.75

1.50

15.0

7.5

120

2.64

0.25

0.69

MPRV120V090

0.90

1.80

7.2

5.0

120

1.80

0.20

0.47

MPRV120V100

1.00

2.00

15.0

10.0

120

2.64

0.18

0.47

MPRV120V110

1.10

2.20

8.2

8.0

120

2.28

0.15

0.38

MPRV120V125

1.25

2.50

20.0

12.5

120

2.88

0.11

0.33

MPRV120V130

1.35

2.70

9.6

10.0

120

2.64

0.12

0.30

MPRV120V135

1.35

2.70

20.0

13.5

120

3.12

0.11

0.30

MPRV120V160

1.60

3.20

11.4

12.0

120

3.12

0.09

0.22

MPRV120V185

1.85

3.70

12.6

12.0

120

3.36

0.08

0.19

MPRV120V200

2.00

4.20

36.0

20.0

120

4.32

0.08

0.21

MPRV120V250

2.50

5.00

15.6

15.0

120

4.44

0.05

0.13

MPRV120V300

3.00

6.00

19.8

17.0

120

4.56

0.04

0.10

MPRV120V375

3.75

7.50

24.0

20.0

120

4.80

0.03

0.08

IH=Hold current-maximum current at which the device will not trip at 23ºC still air.

IT=Trip current-minimum current at which the device will always trip at 23ºC still air.

V MAX=Maximum voltage device can withstand without damage at its rated current (I MAX)

I MAX= Maximum fault current device can withstand without damage at rated voltage (V MAX).

Pd=Typical power dissipated-type amount of power dissipated by the device when in the tripped state in 23ºC still air

environment.

Rmin=Minimum device resistance at 23ºC prior to tripping.

R1MAX=Maximum device resistance at 23ºC measured 1 hour after tripping or reflow soldering of 260ºC for 20 seconds.

Termination pad characteristics

Termination pad materials: Pure Tin

Polymeric PTC

MPRV Series

Rev.7

MPRV bảng dữ liệu(PDF) 2 Page - MERITEK ELECTRONICS CORPORATION

MPRV bảng dữ liệu(HTML) 2 Page - MERITEK ELECTRONICS CORPORATION

Html Pages

1 2 3 4 5 6 7 8

bảng dữ liệu tải về

Link URL