| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
WM8946ECS/R bảng dữ liệu(PDF) 81 Page - Wolfson Microelectronics plc |
|
|
|||||||||||||||||||||||||||||
WM8946ECS/R bảng dữ liệu(HTML) 81 Page - Wolfson Microelectronics plc |
|
81 / 175 page ![]() Production Data WM8946 w PD, July 2012, Rev 4.3 81 The FLL operating frequency, FVCO is set according to the following equation: FVCO = (FREF x N.K x FLL_FRATIO) FREF is the input frequency, as determined by FLL_CLK_REF_DIV. FVCO must be in the range 90-100 MHz. Frequencies outside this range cannot be supported. Note that the output frequencies that do not lie within the ranges quoted above cannot be guaranteed across the full range of device operating temperatures. In order to follow the above requirements for FVCO, the value of FLL_OUTDIV should be selected according to the desired output FOUT, as described in Table 53. OUTPUT FREQUENCY FOUT FLL_OUTDIV 2.8125 MHz – 3.125 MHz 4h (divide by 32) 5.625 MHz – 6.25 MHz 3h (divide by 16) 11.25 MHz – 12.5 MHz 2h (divide by 8) 22.5 MHz – 25 MHz 1h (divide by 4) 45 MHz – 50 MHz 0h (divide by 2) Table 53 Selection of FLL_OUTDIV The value of FLL_FRATIO should be selected as described in Table 54. REFERENCE FREQUENCY FREF FLL_FRATIO 1MHz – 13.5MHz 0h (divide by 1) 256kHz – 1MHz 1h (divide by 2) 128kHz – 256kHz 2h (divide by 4) 16kHz – 128kHz 3h (divide by 8) Less than 16kHz 4h (divide by 16) Table 54 Selection of FLL_FRATIO In order to determine the remaining FLL parameters, the FLL operating frequency, FVCO, must be calculated, as given by the following equation: FVCO = (FOUT x FLL_OUTDIV) The value of FLL_N and FLL_K can then be determined as follows: N.K = FVCO / (FLL_FRATIO x FREF) Note that FREF is the input frequency, after division by FLL_CLK_REF_DIV, where applicable. In FLL Fractional Mode, the fractional portion of the N.K multiplier is held in the FLL_K register field. This field is coded as a fixed point quantity, where the MSB has a weighting of 0.5. Note that, if desired, the value of this field may be calculated by multiplying K by 2^16 and treating FLL_K as an integer value, as illustrated in the following example: If N.K = 8.192, then K = 0.192. Multiplying K by 2^16 gives 0.192 x 65536 = 12582.912 (decimal) = 3126 (hex). |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |