ST802RT1B datasheet(24/58 Pages) STMICROELECTRONICS

24 / 58 page

Registers and descriptors description

ST802RT1A, ST802RT1B

24/58

Doc ID 17049 Rev 1

suppressed from transmission. Resetting the chip restores the default bit values. Reading

the register returns the values last written to the corresponding bits, or else the default

values if no write has been completed since the last chip reset. Even though bit 9 (advertise

100BASE-T4) is writable, it should never be set since the ST802RT1x does not support T4

operation.

Advertised selector: Bits 4:0 of the advertisement register contain the fixed value “00001”,

indicating that the chip belongs to the 802.3 class of PHY transceivers

LP next page: Bit 15 of the link partner ability register returns a value of “1” when the link

partner implements the next page function and has next page information that it wants to

transmit.

LP ack: Bit 14 of the link partner ability register is used by auto-negotiation to indicate that a

device has successfully received its link partner's link code word.

LP remote fault: Bit 13 of the link partner ability register returns a value of “1” when the link

partner signals that a remote fault has occurred. The ST802RT1x simply copies the value to

this register and does not act upon it.

Table 15.

RN05 [0d05, 0x05]: Auto-negotiation link partner ability register

Bit

Bit name

Description

Default

type

Type

LP Next Page

1 -> Link partner desires next page transfer

0 -> Link partner does not desire next page transfer

0RO

Acknowledge

1 -> Link partner acknowledges reception of the ability data

word

0 -> Acknowledge not yet received

0RO

LP Remote

Fault

1 -> Remote fault indicated by link partner

0 -> No remote fault indicated by link partner

0RO

RESERVED

Asymmetric

Pause (full-

duplex)

1 -> LP supports asymmetric pause (MAC level: clause 31,

annex 31B of 802.3u)

0 -> LP has no MAC-based full-duplex flow control.

0RO

LP pause (full-

duplex)

1 -> LP supports symmetric pause (MAC level: clause 31,

annex 31B of 802.3u)

0 -> LP has no MAC-based full-duplex flow control.

0RO

100BASE-T4

1 -> LP supports 100BASE-T4

0 -> LP does not support 100BASE-T4

0RO

100BASE-TX

full duplex

1 -> LP supports 100BASE-TX full-duplex

0 -> LP does not support 100BASE-TX full-duplex

0RO

100BASE-TX

1 -> LP supports 100BASE-TX

0 -> LP does not support 100BASE-TX

0RO

10BASE-T full

duplex

1 -> LP supports 10BASE-T full-duplex

0 -> LP does not support 10BASE-T full-duplex

0RO

10BASE-T

1 -> LP supports 10BASE-T

0 -> LP does not support 10BASE-T

0RO

4:0

LP selector

field

LP's binary encoded protocol selector

00000b

ST802RT1B bảng dữ liệu(PDF) 24 Page - STMicroelectronics

ST802RT1B bảng dữ liệu(HTML) 24 Page - STMicroelectronics

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58

bảng dữ liệu tải về

Link URL