CSD87350Q5D datasheet(9/49 Pages) TI1

9 / 49 page

Test Setup

www.ti.com

Test Setup

4.1

Test and Configuration Software

To change any of the default configuration parameters on the EVM, it is necessary to obtain the TI Fusion

Digital Power Designer software.

4.1.1

Description

The Fusion Digital Power Designer is the graphical user interface (GUI) used to configure and monitor the

Texas Instruments TPS40422 power controller on this evaluation module. The application uses the

PMBus protocol to communicate with the controller over serial bus by way of a TI USB adapter (see

Figure 3).

4.1.2

Features

Some of the tasks you can perform with the GUI include:

•

Turn on or off the power supply output, either through the hardware control line or the PMBus

operation command.

•

Monitor real-time data. Items such as input voltage, output voltage, output current, temperature, and

warnings and faults are continuously monitored and displayed by the GUI.

•

Configure common operating characteristics such as VOUT trim and margin, UVLO, soft-start time,

warning and fault thresholds, fault response, and ON/OFF.

This software is available for download at http://www.ti.com/tool/fusion_digital_power_designer

4.2

Test Equipment

Voltage Source: The input voltage source VIN must be a 0-V to 14-V variable dc source capable of

supplying 15 Adc. Connect VIN to J5 as shown in Figure 2.

Multimeters: It is recommended to use three separate multimeters as shown in Figure 2. One meter to

measure Vin, one to measure Vout1 and the third to measure Vout2.

Output Load: Two variable electronic loads are recommended for the test setup as shown in Figure 2.

Load 1 must be capable of 25 A at voltages as low as 0.9 V. Load 2 must be capable of 20 A at voltages

as low as 3 V.

Oscilloscope: An oscilloscope is recommended for measuring output noise and ripple. Output ripple must

be measured using a Tip-and-Barrel method or better as shown in Figure 4.The scope must be adjusted

to 20-MHz bandwidth, ac coupling at 50 mV/division, and must be set to 1-

µs/division.

Fan: During prolonged operation at high loads, it may be necessary to provide forced air cooling with a

small fan aimed at the EVM. The temperature of the devices on the EVM must be maintained at less than

105

°C.

USB-to-GPIO Interface Adapter: A communications adapter is required between the EVM and the host

computer. This EVM was designed to use the Texas Instruments USB-to-GPIO Adapter (see Figure 3).

This adapter can be purchased at http://www.ti.com/tool/usb-to-gpio.

Recommended Wire Gauge: It is recommended that the voltage drop in the load wires does not exceed

0.2 V total in order to keep the voltage at the load above 1 V. See the following table for recommended

wire gauge and length to achieve a voltage drop of no more than 0.2 V at a 20-A load.

Ohms per Foot

Load Wires Combined Length

Each Wire Length

AWG Gauge

(

Ω)

(Ft)

1.59E-3

6.30

3.15

2.53E-3

3.96

1.98

4.02E-3

2.49

1.25

6.39E-3

1.57

0.78

Using the PWR091EVM Dual-Output DC/DC Analog With PMBus Interface

SLVU638

– January 2012

Submit Documentation Feedback

CSD87350Q5D bảng dữ liệu(PDF) 9 Page - Texas Instruments

CSD87350Q5D bảng dữ liệu(HTML) 9 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49

bảng dữ liệu tải về

Link URL