| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
OPA170AIDBVT bảng dữ liệu(PDF) 13 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
OPA170AIDBVT bảng dữ liệu(HTML) 13 Page - Texas Instruments |
|
13 / 30 page ![]() Time(100 s/div) m +18V -18V 37V PP SineWave ( 18.5V) ± OPA170 OPA170 OPA2170 OPA4170 www.ti.com SBOS557A – AUGUST 2011 – REVISED SEPTEMBER 2011 APPLICATION INFORMATION The OPAx170 family of operational amplifiers This device can operate with full rail-to-rail input provides high overall performance. These devices are 100mV beyond the positive rail, but with reduced ideal for many general-purpose applications. The performance within 2V of the positive rail. The typical excellent offset drift of only 2 µV/°C provides excellent performance in this range is summarized in Table 2. stability over the entire temperature range. In addition, the device offers very good overall PHASE-REVERSAL PROTECTION performance with high CMRR, PSRR, and AOL. As The OPAx170 family has an internal phase-reversal with all amplifiers, applications with noisy or protection. Many op amps exhibit a phase reversal high-impedance power supplies require decoupling when the input is driven beyond its linear capacitors placed close to the device pins. In most common-mode range. This condition is most often cases, 0.1 µF capacitors are adequate. encountered in noninverting circuits when the input is driven beyond the specified common-mode voltage OPERATING CHARACTERISTICS range, causing the output to reverse into the opposite The OPAx170 family of amplifiers is specified for rail. The input of the OPAx170 prevents phase operation from 2.7V to 36V ( ±1.35V to ±18V). Many reversal with excessive common-mode voltage. of the specifications apply from –40°C to +125°C. Instead, the output limits into the appropriate rail. This Parameters that can exhibit significant variance with performance is shown in Figure 37. regard to operating voltage or temperature are presented in the Typical Characteristics. GENERAL LAYOUT GUIDELINES For best operational performance of the device, good printed circuit board (PCB) layout practices are recommended. Low-loss, 0.1 µF bypass capacitors should be connected between each supply pin and ground, placed as close to the device as possible. A single bypass capacitor from V+ to ground is applicable to single-supply applications. COMMON-MODE VOLTAGE RANGE The input common-mode voltage range of the Figure 37. No Phase Reversal OPAx170 series extends 100mV below the negative rail and within 2V of the positive rail for normal operation. Table 2. Typical Performance Range PARAMETER MIN TYP MAX UNIT Input Common-Mode Voltage (V+) – 2 (V+) + 0.1 V Offset voltage 7 mV vs Temperature 12 µV/°C Common-mode rejection 65 dB Open-loop gain 60 dB Gain-bandwidth product 0.3 MHz Slew rate 0.3 V/ µs Copyright © 2011, Texas Instruments Incorporated Submit Documentation Feedback 13 Product Folder Link(s): OPA170 OPA2170 OPA4170 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |