| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PCM2704CDB bảng dữ liệu(PDF) 16 Page - Texas Instruments |
|
|
|
|||||||||||||||||||||||||||||
PCM2704CDB bảng dữ liệu(HTML) 16 Page - Texas Instruments |
|
16 / 40 page ![]() PCM2704C, PCM2705C PCM2706C, PCM2707C SBFS036A – AUGUST 2011 – REVISED JULY 2012 www.ti.com DETAILED DESCRIPTION Clock and Reset For both USB and audio functions, the PCM2704C/5C/6C/7C require a 12-MHz (±500 ppm) clock that can be generated by the onboard oscillator using a 12-MHz crystal resonator. The 12-MHz crystal resonator must be connected to the XTI pin (pin 28 for the PCM2704C/5C, pin 12 for the PCM2706C/7C) and the XTO pin (pin 1 for the PCM2704C/5C, pin 13 for the PCM2706C/7C) with one large (1-M Ω) resistor and two small capacitors; the capacitance of these components depends on the specified load capacitance of the crystal resonator. An external clock can be supplied from XTI (pin 28 for the PCM2704C/5C, pin 12 for the PCM2706C/7C). If an external clock is supplied, XTO (pin 1 for the PCM2704C/5C, pin 13 for the PCM2706C/7C) must be left open. No clock disabling pin is provided; therefore, it is not recommended to use the external clock supply. SSPND (pin 27 for the PCM2704C/5C, pin 11 for the PCM2706C/7C) cannot use clock disabling. The PCM2704C/5C/6C/7C have an internal power-on reset circuit, and it works automatically when VDD (pin 7 for the PCM2704C/5C, pin 21 for the PCM2706C/7C) exceeds 2-V typical (1.6 V to 2.4 V), which is equivalent to VBUS (pin 10 for the PCM2704C/5C, pin 24 for the PCM2706C/7C) exceeding 3-V typical for bus-powered applications. Approximately 700 μs is required until an internal reset release occurs. Operation Mode Selection The PCM2704C/5C/6C/7C have the following mode-select pins. Power Configuration Select/Host Detection PSEL (pin 4 for the PCM2704C/5C, pin 16 for the PCM2706C/7C) is dedicated to selecting the power source. This selection affects the configuration descriptor. While in bus-powered operation, the maximum power consumption from VBUS is determined by the HOST pin (pin 21 for the PCM2704C/5C, pin 3 for the PCM2706C/7C). For self-powered operation, the HOST pin must be connected to VBUS of the USB bus with a pulldown resistor to detect attach and detach. (To avoid excessive suspend current, the pulldown should be a high-value resistor.) Table 3 summarizes the power configuration select options. Table 3. Power Configuration Select PSEL DESCRIPTION 0 Self-powered 1 Bus-powered HOST DESCRIPTION 0 Detached from USB (self-powered)/100 mA (bus-powered) 1 Attached to USB (self-powered)/500 mA (bus-powered) Function Select (PCM2706C/7C Only) FSEL (pin 9) determines the function of the FUNC0–FUNC3 pins (pins 4, 5, 18, and 19) and DOUT (pin 17). When the I2S interface is required, FSEL must be low. Otherwise, FSEL must be high. Table 4 lists the functionality of the FUNC0-FUNC3 pins, based on the FSEL pin. Table 4. Function Select FSEL DOUT FUNC0 FUNC1 FUNC2 FUNC3 0 Data out (I2S) LRCK (I2S) BCK (I2S) SYSCK (I2S) Data in (I2S) 1 S/PDIF data Next track (HID) (1) Previous track (HID) (1) Stop (HID) (1) Play/pause (HID) (1) (1) Valid on the PCM2706C only; no function assigned on the PCM2707C. 16 Submit Documentation Feedback Copyright © 2011–2012, Texas Instruments Incorporated Product Folder Link(s): PCM2704C PCM2705C PCM2706C PCM2707C |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |