LTC5591 datasheet(4/20 Pages) LINER

4 / 20 page

LTC5592

5592f

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

Conversion Gain

RF = 2350MHz

7.1

Input 3rd Order Intercept

RF = 2350MHz

22.3

dBm

SSB Noise Figure

RF = 2350MHz

10.2

Input 1dB Compression

RF = 2350MHz, VCCIF = 3.3V

RF = 2350MHz, VCCIF = 5V

11.3

12.6

dBm

Note 1: Stresses beyond those listed under Absolute Maximum Ratings

may cause permanent damage to the device. Exposure to any Absolute

Maximum Rating condition for extended periods may affect device

reliability and lifetime.

Note 2: The LTC5592 is guaranteed functional over the case operating

temperature range of –40°C to 105°C (

θJC = 7°C/W).

Note 3: SSB Noise Figure measured with a small-signal noise source,

bandpass filter and 6dB matching pad on RF input, bandpass filter and

6dB matching pad on the LO input, and no other RF signals applied.

Note 4: Channel A to channel B isolation is measured as the relative IF

output power of channel B to channel A, with the RF input signal applied to

channel A. The RF input of channel B is 50Ω terminated and both mixers

are enabled.

AC ELECTRICAL CHARACTERISTICS

VCC = 3.3V, VCCIF = 3.3V, ENA = ENB = High, TC = 25°C, PLO = 0dBm,

PRF = –3dBm (Δf = 2MHz for two tone IIP3 tests), unless otherwise noted. Test circuit shown in Figure 1. (Notes 2, 3)

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

SSB Noise Figure Under Blocking

fRF = 2400MHz, fLO = 2210MHz, fBLOCK = 2500MHz

PBLOCK = 5dBm

PBLOCK = 10dBm

15.3

21.2

2RF-2LO Output Spurious Product

(fRF = fLO + fIF/2)

fRF = 2255MHz at –10dBm, fLO = 2160MHz,

fIF = 190MHz

–68

dBc

3RF-3LO Output Spurious Product

(fRF = fLO + fIF/3)

fRF = 2223.33MHz at –10dBm, fLO = 2160MHz,

fIF = 190MHz

–74

dBc

Input 1dB Compression

fRF = 2350MHz, VCCIF = 3.3V

fRF = 2350MHz, VCCIF = 5V

14.6

dBm

Low Side LO Downmixer Application: ISEL = Low, RF = 1900MHz to 2700MHz, IF = 190MHz, fLO = fRF – fIF

Low Power Mode, Low Side LO Downmixer Application: ISEL = High, RF = 1900MHz to 2700MHz, IF = 190MHz, fLO = fRF – fIF

PARAMETER

CONDITIONS

MIN

TYP

MAX

UNITS

Conversion Gain

RF = 1750MHz

RF = 1950MHz

RF = 2150MHz

9.1

8.7

8.3

Conversion Gain Flatness

RF = 1950 ±30MHz, LO = 2140MHz, IF = 190 ±30MHz

±0.33

Conversion Gain vs Temperature

TC = –40ºC to 105ºC, RF = 1900MHz

–0.005

dB/°C

Input 3rd Order Intercept

RF = 1750MHz

RF = 1950MHz

RF = 2150MHz

25.3

25.4

25.1

dBm

SSB Noise Figure

RF = 1750MHz

RF = 1950MHz

RF = 2150MHz

9.2

9.8

10.4

SSB Noise Figure Under Blocking

fRF = 1950MHz, fLO = 2140MHz, fBLOCK = 1850MHz

PBLOCK = 5dBm

PBLOCK = 10dBm

16.5

22.7

2LO-2RF Output Spurious Product

(fRF = fLO – fIF/2)

fRF = 2045MHz at –10dBm, fLO = 2140MHz,

fIF = 190MHz

–68

dBc

3LO-3RF Output Spurious Product

(fRF = fLO – fIF/3)

fRF = 2076.67MHz at –10dBm, fLO = 2140MHz,

fIF = 190MHz

–75

dBc

Input 1dB Compression

RF = 1950MHz, VCCIF = 3.3V

RF = 1950MHz, VCCIF = 5V

10.6

14.0

dBm

High Side LO Downmixer Application: ISEL = Low, RF = 1600MHz to 2300MHz, IF = 190MHz, fLO = fRF + fIF

LTC5591 bảng dữ liệu(PDF) 4 Page - Linear Technology

LTC5591 bảng dữ liệu(HTML) 4 Page - Linear Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

bảng dữ liệu tải về

Link URL