ZXLD1371QESTTC datasheet(26/42 Pages) DIODES

26 / 42 page

ZXLD1371

Document number: DS35436 Rev. 1 - 2

26 of 42

www.diodes.com

February 2012

A Product Line of

Diodes Incorporated

Applications Information (cont.)

This will give small enough ILED error for most practical purposes. Satisfactory operation will be obtained if VRS is more than

about 80mV. This means GI_ADJ should be greater than (1-DMIN) * 80/225 = (1- DMIN) * 0.355.

There is also a maximum limit on VRS which gives a maximum limit for GI_ADJ. If VRS exceeds approximately 300mV, or

133% of 225mV, the STATUS output may indicate an over-current condition. This will happen for larger DMAX. Therefore,

together with the requirement of Equation 13, the recommended range for GI_ADJ is

0.355 ( 1-DMIN) < GI_ADJ < 1.33 ( 1-DMAX )

Equation 15

An optimum compromise for GI_ADJ has been suggested, i.e.

GI_ADJAUTO = 1 - DMAX

Equation 16

This value has been used for the “Automatic” setting of the web Calculator. If 1-DMAX is less than 0.2, then GI_ADJ is set to

0.2. If 1- DMAX is greater than 0.5 then GI_ADJ is set to 0.5.

Once GI_ADJ has been selected, a value of RGI1 can be selected from Equation 12. Then RGI2 is calculated as follows,

rearranging Equation 2:

RGI2 = RGI1

1-GI_ADJ

GI_ADJ

Equation 17

For example to drive 12 LEDS at a current of 350mA from a 12V supply requires Boost configuration. Each LED has a

forward voltage of 3.2V at 350mA, so Vout = 3.2*12 = 38.4V. From Equation 6, the duty cycle is approximately

VOUT-VIN

VOUT

38.4-12

38.4

= 0.6875

From Equation 16, we set GI_ADJ to 1 – D = 0.3125.

IF RGI1 = 33kΩ, then from Equation 17, RGI2 = 33000 * ( 1 -0.3125 ) / 0.3125 = 72.6kΩ. Let us choose the preferred value

RGI2 = 75kΩ. Now GI_ADJ is adjusted to the new value, using Equation 2.

GI_ADJ =

RGI1

RGI1 +RGI2

33k

33k +75k

=0.305

Now we calculate Rs from Equation 11. Assume ADJ is connected to REF.

RSBoostBB =

0.225

ILED

GI_ADJ

VADJ

VREF

0.225

0.35

* 0.305 = 0.196

Ω

A preferred value of RSBoostBB = 0.2Ω will give the desired LED current with an error of 2% due to the preferred value

selection.

Table 1 shows typical resistor values used to determine the GI_ADJ ratio with E24 series resistors.

Table 1

GI ratio

RGI1

RG2

0.2

30k

120k

0.25

33k

100k

0.3

39k

91k

0.35

30k

56k

0.4

100k

150k

0.45

51k

62k

0.5

30k

This completes the LED current setting.

ZXLD1371QESTTC bảng dữ liệu(PDF) 26 Page - Diodes Incorporated

ZXLD1371QESTTC bảng dữ liệu(HTML) 26 Page - Diodes Incorporated

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

bảng dữ liệu tải về

Link URL