EPC120 datasheet(2/27 Pages) EPC

2 / 27 page

epc120

Absolute Maximum Ratings (Notes 1, 2)

Recommended Operating Conditions

Voltage to any pin except VDD

Supply Voltage on 2-wire bus VDD

Programming Voltage on 2-wire bus VDD

Input current at any pin except LED

Power consumption with maximum load

Storage Temperature Range (TS)

Lead Temperature solder, 4 sec. (TL)

-0.3V to VDD+0.3 V

-0.3V to +8.0V

-6mA to +6 mA

125mW

-55°C to +155°C

+260°C

Operating Voltage on 2-wire bus VDD

Programming Voltage on VDD

Operating Temperature (TO)

Relative Humidity (non-condensing)

Min.

4.5

7.0

-40°

Max.

5.5

8.0

+85

+95

Units

°C

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended operating conditions

indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specific -

ations and test conditions, see Electrical Characteristics.

Note 2: This device is a highly sensitive CMOS ac current amplifier with an ESD rating of JEDEC HBM class 0 (<250V). Handling and

assembly of this device should only be done at ESD protected workstations.

Electrical Characteristics

VDD = 4.5V … 5.5V, -40°C < TA < +85°C, unless otherwise specified

General Data

Symbol

Parameter

Conditions/Comments

Values

Units

Min.

Typ.

Max.

VPP

Ripple on supply voltage,

peak to peak

2-wire interface Vdet

Input pulse IPD NST

50mV

48nA

150

100mV

72nA

350

200mV

108nA

600

IDD_OP

Current consumption

in operation mode IPD = 0 mA

Vdet

Detection level for 2-wire interface

configurable

200

IMOD

Modulation current for 2-wire inter-

face

6.4

9.8

fclk

Reference clock

Internal oscillator

MHz

dfclk

Temperature drift of the oscillator

640

ppm/K

VPUP

Power-up Threshold Voltage

The voltage at VDD33 when the device starts up

2.4

VIH

INPUT

Logical high (VN can be either VDD or VDD33)

0.7 *VN

VIL

INPUT

Logical low (VN can be either VDD or VDD33)

GND

0.3 *VN

ILEAKD

Input leakage current

µA

VOH

Output high voltage

@ 4mA sink except pin SCK/LED

VDD- 0.5

VOL

Output low voltage

@ 4mA source

0.5

ISCK/LED

Source current

@ PIN SCK / LED

0.7

1.3

VHist

Schmitt Trigger Hysteresis

0.1

RPU

Pull-Up Resistor

200

kΩ

IPDDC

DC Photo Diode Current

generated by ambient light with no effect to the

sensitivity

0.0

CPD

Photodiode Capacitance

IN_Imin

Input related noise

@ IPDDC =0

nA RMS

IN_Imax

Input related noise

@ IPDDC =IPDDCMax

nA RMS

IPDN

Photo Current Sensitivity, normal

threshold

Parameter SENSN = 011 (60nA). TPulse = 6µs

Photodiode pulse to generate a status “pulse detected”

IPDH

Photo Current Sensitivity, upper

threshold

Parameter SENSH = 011 (96nA). TPulse = 6µs

Photodiode pulse to generate a status “pulse detected”

1.4

1.6

1.8

IPDN

Characteristics subject to change without notice

Datasheet epc12x - V2.1

EPC120 bảng dữ liệu(PDF) 2 Page - Espros Photonics corp

EPC120 bảng dữ liệu(HTML) 2 Page - Espros Photonics corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

bảng dữ liệu tải về

Link URL