LC877C64C/56C/48C/40C/32C/24C

No.A0135-13/21

Continued from preceding page.

Specification

Parameter

Symbol

Pin/Remarks

Conditions

VDD [V]

min

typ

max

unit

4.5 to 5.5

15

35

80

Resistance of

pull-up MOS Tr.

Rpu

• Ports 0, 1, 7

• Ports A, B, D, E

VOH=0.9VDD

2.2 to 4.5

18

50

150

k

Ω

VHYS(1)

• Ports 1, 7

• RES

2.2 to 5.5

0.1VDD

Hysterisis voltage

VHYS(2)

Port 87 small

signal input

2.2 to 5.5

0.1VDD

V

Pin capacitance

CP

All pins

• All Other Terminals Connected

To VSS.

• F=1MHz

• Ta=25

°C

2.2 to 5.5

10

pF

Input sensitivity

Vsen

Port 87 small

signal input

2.2 to 5.5

0.12VDD

Vp-p

Serial Input/Output Characteristics at Ta = -30°C to +70°C, VSS1 = VSS2 = VSS3 = 0V

1. SIO0 Serial I/O Characteristics (Note 4-1-1)

Specification

Parameter

Symbol

Pin/Remarks

Conditions

VDD [V]

min

typ

max

unit

Frequency

tSCK(1)

2

Low level

pulse width

tSCKL(1)

1

tSCKH(1)

See Fig. 6.

1

High level

pulse width

tSCKHA(1)

SCK0(P12)

• Continuous data

transmission/reception mode

• See Fig. 6.

• (Note 4-1-2)

2.2 to 5.5

4

Frequency

tSCK(2)

4/3

tCYC

Low level

pulse width

tSCKL(2)

1/2

tSCKH(2)

• CMOS output selected

• See Fig. 6.

1/2

tSCK

High level

pulse width

tSCKHA(2)

SCK0(P12)

• Continuous data

transmission/reception mode

• CMOS output selected

• See Fig. 6.

2.2 to 5.5

tSCKH(2)

+2tCYC

tSCKH(2)

+(10/3)

tCYC

tCYC

Data setup time

tsDI(1)

2.2 to 5.5

0.03

Data hold time

thDI(1)

SB0(P11),

SI0(P11)

• Must be specified with respect

to rising edge of SIOCLK.

• See Fig. 6.

2.2 to 5.5

0.03

tdD0(1)

• Continuous data

transmission/reception mode

• (Note 4-1-3)

2.2 to 5.5

(1/3)tCYC

+0.05

tdD0(2)

• Synchronous 8-bit mode

• (Note 4-1-3)

2.2 to 5.5

1tCYC

+0.05

Output delay

time

tdD0(3)

SO0(P10),

SB0(P11)

(Note 4-1-3)

2.2 to 5.5

(1/3)tCYC

+0.15

µs

Note 4-1-1: These specifications are theoretical values. Add margin depending on its use.

Note 4-1-2: To use serial-clock-input in continuous trans/rec mode, a time from SI0RUN being set when serial clock

is "H" to the first negative edge of the serial clock must be longer than tSCKHA.

Note 4-1-3: Must be specified with respect to falling edge of SIOCLK. Must be specified as the time to the beginning

of output state change in open drain output mode. See Fig. 6.