HIP4086APZ datasheet(5/16 Pages) INTERSIL

5 / 16 page

HIP4086, HIP4086A

FN4220.7

June 1, 2011

Absolute Maximum Ratings

Thermal Information

(Note 7)

Supply Voltage, VDD Relative to GND. . . . . . . . . . . . . . . . . . . . . -0.3V to 16V

Logic Inputs (xLI, xHI) . . . . . . . . . . . . . . . . . . . . . . . GND - 0.3v to VDD + 0.3V

Voltage on xHS . . . . . . . . . . . . . . -6V (Transient) to 85V (-40°C to +150°C)

Voltage on xHB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VxHS - 0.3V to VxHS +VDD

Voltage on xLO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSS - 0.3V to VDD +0.3V

Voltage on xHO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VxHS - 0.3V to VxHB +0.3V

Phase slew rate (on xHS). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns

Maximum Recommended Operating

Conditions

Supply Voltage, VDD Relative to GND. . . . . . . . . . . . . . . . . . . . . . . 7V to 15V

Logic Inputs (xLI, xHI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to VDD

Voltage on xHB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VxHS + VDD

Voltage on xHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 80V

Ambient Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-40°C to +125°C

Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . .-40°C to +150°C

Thermal Resistance (Typical)

θJA (°C/W) θJC (°C/W)

SOIC Package (Notes 4, 6) . . . . . . . . . . . . .

SOIC Package HIP4086AABZ (Notes 5, 6)

PDIP* Package (Notes 4, 6) . . . . . . . . . . . .

Storage Temperature Range. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C

Operating Junction Temp Range . . . . . . . . . . . . . . . . . . . .-40°C to +150°C

Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

*Pb-free PDIPs can be used for through-hole wave solder processing only.

They are not intended for use in Reflow solder processing applications.

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product

reliability and result in failures not covered by warranty.

NOTES:

θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.

6. For

θJC, the “case temp” location is taken at the package top center.

7. Replace x with A, B, or C.

DC Electrical Specifications VDD = VxHB = 12V, VSS = VxHS = 0V, RDEL = 20k, RUV = ∞, Gate Capacitance (CGATE) = 1000pF,

unless otherwise specified. Boldface limits apply over the operating junction temperature range, -40°C to +150°C.

PARAMETER

TEST CONDITIONS

TJ = +25°C

TJ = -40°C TO +150°C

UNITS

MIN

(Note 9)

TYP

MAX

(Note 9)

MIN

(Note 9)

MAX

(Note 9)

SUPPLY CURRENTS

VDD Quiescent Current

xHI = 5V, xLI = 5V (HIP4086)

2.7

3.4

4.2

2.1

4.3

xHI = 5V, xLI = 5V (HIP4086A)

2.3

2.4

2.6

2.1

2.7

VDD Operating Current

f = 20kHz, 50% Duty Cycle (HIP4086)

6.3

8.25

10.5

511

f = 20kHz, 50% Duty Cycle (HIP4086A)

3.1

3.6

4.1

2.8

4.4

xHB On Quiescent Current

xHI = 0V (HIP4086)

100

µA

xHI = 0V (HIP4086A)

100

200

µA

xHB Off Quiescent Current

xHI = VDD (HIP4086)

0.6

0.8

1.3

0.5

1.4

xHI = VDD (HIP4086A)

0.8

0.9

0.7

1.2

xHB Operating Current

f = 20kHz, 50% Duty Cycle (HIP4086)

0.7

0.9

1.3

2.0

f = 20kHz, 50% Duty Cycle (HIP4086A)

0.8

0.9

1.2

xHB, xHS Leakage Current

VxHS = 80V, VxHB = 93V

µA

Charge Pump, HIP4086 only, (Note 8)

QPUMP Output Voltage

No Load

11.5

12.5

10.5

14.5

QPUMP Output Current

VxHS = 12V, VxHB = 22V

100

130

140

µA

UNDERVOLTAGE PROTECTION

VDD Rising Undervoltage Threshold

RUV open

6.2

7.1

8.0

6.1

8.1

VDD Falling Undervoltage Threshold

RUV open

5.75

6.6

7.5

5.6

7.6

Minimum Undervoltage Threshold

RUV = VDD

6.2

6.8

4.9

6.9

HIP4086APZ bảng dữ liệu(PDF) 5 Page - Intersil Corporation

HIP4086APZ bảng dữ liệu(HTML) 5 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

bảng dữ liệu tải về

Link URL