| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ADM1276 bảng dữ liệu(PDF) 39 Page - Analog Devices |
|
|
|||||||||||||||||||||||||||||
ADM1276 bảng dữ liệu(HTML) 39 Page - Analog Devices |
|
39 / 48 page ![]() ADM1276 Rev. 0 | Page 39 of 48 STATUS_INPUT Code: 0x7C, read byte. Value after reset: 0x00. Table 23. Bit Descriptions for STATUS_INPUT Command Bits Bit Name Behavior Settings Description [7] VIN_OV_FAULT Latched 0 No overvoltage detected on the OV pin. 1 An overvoltage was detected on the OV pin. [6] VIN_OV_WARN Latched 0 No overvoltage condition on the input supply detected by the power monitor. 1 An overvoltage condition on the input supply was detected by the power monitor. [5] VIN_UV_WARN Latched 0 No undervoltage condition on the input supply detected by the power monitor. 1 An undervoltage condition on the input supply was detected by the power monitor. [4] VIN_UV_FAULT Latched 0 No undervoltage detected on the UV pin. 1 An undervoltage was detected on the UV pin. [3:1] Reserved 000 Always reads as 000. [0] PIN_OP_WARN Latched 0 No overpower condition on the input supply detected by the power monitor. 1 An overpower condition on the input supply was detected by the power monitor. STATUS_MFR_SPECIFIC Code: 0x80, read byte. Value after reset: 0x00. Table 24. Bit Descriptions for STATUS_MFR_SPECIFIC Command Bits Bit Name Behavior Settings Description [7] FET_HEALTH_BAD Latched 0 FET behavior appears to be as expected. 1 FET behavior suggests that the FET may be shorted. [6] UV_CMP_OUT Live 0 Input voltage to UV pin is above threshold. 1 Input voltage to UV pin is below threshold. [5] OV_CMP_OUT Live 0 Input voltage to OV pin is below threshold. 1 Input voltage to OV pin is above threshold. [4] Reserved 0 Always reads as 0. [3] HS_INLIM Latched 0 The ADM1276 has not actively limited the current into the load. 1 The ADM1276 has actively limited current into the load. This bit differs from the IOUT_OC_FAULT bit in that the HS_INLIM bit is set immediately, whereas the IOUT_OC_FAULT bit is not set unless the time limit set by the capacitor on the TIMER pin elapses. [2:1] HS_SHUTDOWN_CAUSE Latched 00 The ADM1276 is either enabled and working correctly, or has been shut down using the OPERATION command. 01 An IOUT_OC_FAULT condition occurred that caused the ADM1276 to shut down. 10 A VIN_UV_FAULT condition occurred that caused the ADM1276 to shut down. 11 A VIN_OV_FAULT condition occurred that caused the ADM1276 to shut down. [0] IOUT_WARN2 Latched 0 No overcurrent condition on the output supply detected by the power monitor using the IOUT_WARN2_LIMIT command. 1 An undercurrent or overcurrent condition on the output supply was detected by the power monitor using the IOUT_WARN2_LIMIT command. The polarity of the threshold condition is set by the IOUT_WARN2_SELECT bit using the DEVICE_CONFIG command. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |