MIC35152WD datasheet(3/8 Pages) MICREL

3 / 8 page

Micrel, Inc.

MIC35152

October 2009

M9999-102309-A

Absolute Maximum Ratings

(1)

Supply Voltage (VIN)..................................... –0.3V to +6.5V

Enable Input Voltage (VEN)........................... –0.3V to +6.5V

Power Dissipation .....................................Internally Limited

Junction Temperature .........................–40°C ≤ TJ ≤ +125°C

Storage Temperature (Ts) ...................–65°C ≤ TJ ≤ +150°C

Lead Temperature (soldering, 5sec.)......................... 260°C

ESD Rating................................................................ Note 3

Operating Ratings

(2)

Supply voltage (VIN) ................................... +2.25V to +6.0V

Enable Input Voltage (VEN)................................ 0V to +6.0V

Junction Temperature Range .............–40°C ≤ TJ ≤ +125°C

Maximum Power Dissipation..................................... Note 4

Package Thermal Resistance

TO-252 (θJC) ........................................................3°C/W

TO-252 (θJA) ......................................................56°C/W

Electrical Characteristics

(5)

TJ = 25°C with VIN = VEN = VOUT + 1V; IOUT = 10mA; bold values indicate –40°C < TJ < +125°C, unless otherwise noted.

Parameter

Condition

Min

Typ

Max

Units

Output Voltage Line Regulation

VIN = VOUT +1.0V to 6.0V

0.06

0.5

Output Voltage Load Regulation

IOUT = 10mA to 1.5A

0.2

IOUT = 750mA

225

350

Dropout Voltage, VIN – VOUT

Note 6

IOUT = 1.5A

365

600

Ground Pin Current, Note 7

IOUT = 1.5A

Ground Pin Current in Shutdown

VIL ≤ 0.5V, VIN = VOUT + 1V

1.0

µA

Current Limit

VOUT = 0

2.7

4.0

Start-up Time

VEN = VIN, IOUT = 10mA, COUT = 47µF

150

µs

Enable Input

Regulator enable

2.25

Enable Input Threshold

Regulator shutdown

0.8

VIL ≤ 0.8V (regulator shutdown)

µA

Enable Pin Input Current

VIH ≥ 2.25V (regulator enabled)

µA

Adjust Pin

1.228

1.240

1.252

Reference Voltage

1.215

1.265

Reference Voltage Temp.

Coefficient

Note 8

ppm/°C

Adjust Pin Bias Current

120

Adjust Pin Bias Current Temp.

Coefficient

0.1

nA/°C

Notes:

Exceeding the absolute maximum rating may damage the device.

The device is not guaranteed to function outside its operating rating.

Devices are ESD sensitive. Handling precautions recommended.

PD(MAX) = (TJ(MAX) – TA) / θJA, where θJA, depends upon the printed circuit layout. See “Applications Information.”

Specification for packaged product only.

VDO = VIN – VOUT when VOUT decreased to 98% of its nominal output voltage with VIN = VOUT +1V. For output voltages below 1.75V, dropout voltage

speciﬁcation does not apply due to a minimum input operating voltage of 2.25V.

IGND is the quiescent current. IIN = IGND + IOUT.

Thermal regulation is deﬁned as the change in output voltage at a time t after a change in power dissipation is applied, excluding load or line

regulation effects. Speciﬁcations are for a 200mA load pulse at VIN = 6V for t = 10ms.

MIC35152WD bảng dữ liệu(PDF) 3 Page - Micrel Semiconductor

MIC35152WD bảng dữ liệu(HTML) 3 Page - Micrel Semiconductor

Html Pages

1 2 3 4 5 6 7 8

bảng dữ liệu tải về

Link URL