AP1086 datasheet(3/10 Pages) DIODES

3 / 10 page

AP1086

1.5A LOW DROPOUT POSITIVE ADJUSTABLE OR

FIXED-MODE REGULATOR

AP1086

Document number: DS31028 Rev. 6 - 2

3 of 10

www.diodes.com

June 2010

Electrical Characteristics (Under Operating Conditions)

Parameter

Conditions

Min

Typ.

Max

Unit

Reference Voltage

AP1086-Adj

TA = 25

οC, (V

IN-VOUT)= 1.5V,IO = 10mA

1.225

1.250

1.275

Output Voltage

AP1086-1.5

IOUT = 10mA, TA = 25

οC, 3V≦V

IN≦12V

1.470

1.500

1.530

AP1086-1.8

IOUT = 10mA, TA = 25

οC, 3.3V≦V

IN≦12V

1.764

1.800

1.836

AP1086-2.5

IOUT = 10mA, TA = 25

οC, 4V≦V

IN≦12V

2.450

2.500

2.550

AP1086-3.3

IOUT = 10mA, TA = 25

οC, 4.8V≦V

IN≦12V

3.235

3.300

3.365

AP1086-5.0

IOUT = 10mA, TA = 25

οC, 6.5V≦V

IN≦12V

4.900

5.000

5.100

Line Regulation

AP1086-XXX

IO = 10mA, VOUT+1.5V<VIN<12V

0.2

Load Regulation

AP1086-Adj

VIN = 3.3V, 0mA<Io<1.5A, TA = 25

οC

(Note 2, 3)

AP1086-1.5

VIN = 3V, 0mA<Io<1.5A, TA = 25

οC

(Note 2, 3)

AP1086-1.8

VIN = 3.3V, 0mA<Io<1.5A, TA = 25

οC

(Note 2, 3)

AP1086-2.5

VIN = 4V, 0mA<Io<1.5A, TA = 25

οC

(Note 2, 3)

AP1086-3.3

VIN = 5V, 0≦IOUT≦1.5A, TA = 25

οC,

TJ = 25

oC (Note 2, 3)

AP1086-5.0

VIN = 8V, 0≦IOUT≦1.5A, TA = 25

οC,

TJ = 25

oC (Note 2, 3)

Dropout Voltage

(VIN-VOUT)

AP1086-Adj/-2.5/

-3.3/-3.6/-5.0

IOUT = 1.5A, ΔVOUT = 1%VOUT

1.3

1.4

Current Limit

AP1086-Adj/-2.5/

-3.3/-3.6/-5.0

(VIN-VOUT) = 5V

1. 6

Minimum Load

Current (Note 4)

AP1086-XXX

oC≦T

J≦125

Thermal Regulation

TA = 25

οC, 30ms pulse

0.008

0.04

%/W

Ripple Rejection

f = 120Hz,COUT = 25uF Tantalum, IOUT = 1.5A

AP1086-XXX

VIN = VOUT+3V

RMS Noise (% of VOUT)

10Hz

≤ f ≤ 10KHz

0.003

Temperature Stability

IO = 10mA

0.5

θJA Thermal Resistance

Junction-to-Ambient

(No heat sink; No air flow)

TO252-3L

TO263-3L

TO220-3L

101

oC/W

θJC Thermal Resistance

Junction-to-Case

TO252-3L: Control Circuitry/Power Transistor

TO263-3L: Control Circuitry/Power Transistor

TO220-3L: Control Circuitry/Power Transistor

0.65/2.7

oC/W

Notes:

2. See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant

junction temperature by low duty cycle pulse testing. Load regulation is measured at the output lead = 1/18” from the package.

3. Line and load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the difference in input and

output and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.

4. Quiescent current is defined as the minimum output current required in maintaining regulation. At 12V input/output differential the device is

guaranteed to regulate if the output current is greater than 10mA.

AP1086 bảng dữ liệu(PDF) 3 Page - Diodes Incorporated

AP1086 bảng dữ liệu(HTML) 3 Page - Diodes Incorporated

Html Pages

1 2 3 4 5 6 7 8 9 10

bảng dữ liệu tải về

Link URL