| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
R5F36CAMDFB bảng dữ liệu(PDF) 53 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
R5F36CAMDFB bảng dữ liệu(HTML) 53 Page - Renesas Technology Corp |
|
53 / 94 page ![]() REJ03B0277-0100 Rev.1.00 Jul.15, 2009 Page 51 of 90 M16C/6C Group 5. Electrical Characteristics Notes: 1. VCC1 = 2.7 to 5.5 V at Topr = 0 to 60°C unless otherwise specified. 2. Definition of program and erase cycles The program and erase cycles refer to the number of per-block erasures. If the program and erase cycles are n (n=10,000), each block can be erased n times. For example, if a 4 Kbyte block is erased after writing two word data 1,024 times, each to a different address, this counts as one program and erase cycles. Data cannot be written to the same address more than once without erasing the block (rewrite prohibited). 3. Cycles to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed). 4. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example, when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups before erasing them all in one operation. In addition, averaging the erasure cycles between blocks A and B can further reduce the actual erasure cycles. It is also advisable to retain data on the erasure cycles of each block and limit the number of erase operations to a certain number. 5. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase command at least three times until the erase error does not occur. 6. Customers desiring program/erase failure rate information should contact their Renesas technical support representative. 7. The data hold time includes time that the power supply is off or the clock is not supplied. Table 5.11 Flash Memory (Data Flash) Electrical Characteristics Symbol Parameter Conditions Standard Unit Min. Typ. Max. - Program/erase cycles (2, 4, 5) VCC1 = 3.3 V, Topr = 25°C 10,000 (3) times - Two words program time VCC1 = 3.3 V, Topr = 25°C 300 4000 μs - Lock bit program time VCC1 = 3.3 V, Topr = 25°C 140 3000 μs - Block erase time VCC1 = 3.3 V, Topr = 25°C 0.2 3.0 s - Program, erase voltage 2.7 5.5 V - Read voltage 2.7 5.5 V - Program, erase temperature 0 60 °C tPS Flash Memory Circuit Stabilization Wait Time 50 μs - Data hold time (7) Ambient temperature = 55 °C 20 year |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |