| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
TUSB3210 bảng dữ liệu(PDF) 14 Page - Texas Instruments |
|
|
|||||||||||||||||||||||||||||
TUSB3210 bảng dữ liệu(HTML) 14 Page - Texas Instruments |
|
14 / 45 page ![]() www.ti.com 2.2.3 PUR_n: GPIO Pullup Register for Port n (n = 0 to 3) 2.2.4 INTCFG: Interrupt Configuration 2.2.5 WDCSR: Watchdog Timer, Control, and Status Register TUSB3210 Universal Serial Bus General-Purpose Device Controller SLLS466F – FEBRUARY 2001 – REVISED AUGUST 2007 PUR_0: GPIO pullup register for port 0 PUR_1: GPIO pullup register for port 1 PUR_2: GPIO pullup register for port 2 PUR_3: GPIO pullup register for port 3 7 6 5 4 3 2 1 0 PORT_n.7 PORT_n.6 PORT_n.5 PORT_n.4 PORT_n.3 PORT_n.2 PORT_n.1 PORT_n.0 R/W R/W R/W R/W R/W R/W R/W R/W BIT NAME RESET FUNCTION 0–7 PORT_n.N 0 The MCU can write to this register. If the MCU sets this bit to 1, the internal pullup resistor is (N = 0 to 7) disconnected from the pin. If the MCU clears this bit to 0, the pullup resistor is connected to the pin. The pullup resistor is connected to the VCC power supply. 7 6 5 4 3 2 1 0 RSV RSV RSV RSV I3 I2 I1 I0 R/O R/O R/O R/O R/W R/W R/W R/W BIT NAME RESET FUNCTION 0–3 I[3:0] 0010 The MCU can write to this register to set the interrupt delay time for port 2 on the MCU. The value of the lower nibble represents the delay in ms. Default after reset is 2 ms. I[3:0] Delay 0000 5 ms 0001 5 ms 0010 2 ms (default) 0011 3 ms 0100 4 ms 0101 5 ms 0110 6 ms 0111 7 ms 1000 8 ms 1001 9 ms 1010 10 ms 1011 5 ms 1100 5 ms 1101 5 ms 1110 5 ms 1111 5 ms 4–7 RSV 0 Reserved A watchdog timer (WDT) with 1-ms clock is provided. The watchdog timer works only when a USB start-of-frame has been detected by the TUSB3210. If this register is not accessed for a period of 32 ms, the WDT counter resets the MCU (see Figure 2-2, Reset Diagram). When the IDL bit in PCON is set, the WDT is suspended until an interrupt is detected. At this point, the IDL bit is cleared and the WDT resumes operation. The WDE bit of this register is cleared only on power up or USB reset (if enabled). When the MCU writes a 1 to the WDE bit of this register, the WDT starts running. (W/O notation indicates write only by the MCU.) Functional Description 14 Submit Documentation Feedback |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |