P89LPC983FDH datasheet(11/85 Pages) NXP

11 / 85 page

P89LPC980_982_983_985_2

Preliminary data sheet

Rev. 02 — 8 February 2010

11 of 85

NXP Semiconductors

P89LPC980/982/983/985

8-bit microcontroller with accelerated two-clock 80C51 core

P0.6/CMP1/KBI6

I/O

P0.6 — Port 0 bit 6. High current source.

CMP1 — Comparator 1 output.

KBI6 — Keyboard input 6.

P0.7/KBI7/T1

I/O

P0.7 — Port 0 bit 7. High current source.

I/O

T1 — Timer/counter 1 external count input or overflow output.

KBI7 — Keyboard input 7.

P1.0 to P1.7

I/O, I

[1]

Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type, except for

three pins as noted below. During reset Port 1 latches are configured in the input

only mode with the internal pull-up disabled. The operation of the configurable

Port 1 pins as inputs and outputs depends upon the port configuration selected.

Each of the configurable port pins are programmed independently. Refer to Section

7.16.1 “Port configurations” and Table 13 “Static characteristics” for details. P1.2 to

P1.3 are open drain when used as outputs. P1.5 is input only.

All pins have Schmitt trigger inputs.

Port 1 also provides various special functions as described below:

P1.0/TXD

I/O

P1.0 — Port 1 bit 0.

TXD — Transmitter output for serial port.

P1.1/RXD/T2EX

I/O

P1.1 — Port 1 bit 1.

RXD — Receiver input for serial port.

T2EX — Timer/counter 2 external capture input.

P1.2/SCL/T0

I/O

P1.2 — Port 1 bit 2 (open-drain when used as output).

I/O

T0 — Timer/counter 0 external count input or overflow output (open-drain when

used as output).

I/O

SCL — I2C-bus serial clock input/output.

P1.3/INT0/SDA/

I/O

P1.3 — Port 1 bit 3 (open-drain when used as output).

INT0 — External interrupt 0 input.

I/O

SDA — I2C-bus serial data input/output.

I/O

T4 — Timer/counter 4 external count input or overflow output.

P1.4/INT1/T4EX/

I/O

P1.4 — Port 1 bit 4. High current source.

INT1 — External interrupt 1 input.

T4EX — Timer/counter 4 external capture input.

SS — SPI Slave select. (pin remap)

P1.5/RST

P1.5 — Port 1 bit 5 (input only).

RST — External Reset input during power-on or if selected via UCFG1. When

functioning as a reset input, a LOW on this pin resets the microcontroller, causing

I/O ports and peripherals to take on their default states, and the processor begins

execution at address 0. Also used during a power-on sequence to force ISP mode.

P1.6/MISO

I/O

P1.6 — Port 1 bit 6. High current source.

I/O

MISO — SPI master in slave out.When configured as master, this pin is input,

when configured as slave, this pin is output. (pin remap)

Table 3.

Pin description …continued

Symbol

Type

Description

PLCC28,

TSSOP28

P89LPC983FDH bảng dữ liệu(PDF) 11 Page - NXP Semiconductors

P89LPC983FDH bảng dữ liệu(HTML) 11 Page - NXP Semiconductors

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85

bảng dữ liệu tải về

Link URL