AM1808AZCE3 datasheet(44/264 Pages) TI

44 / 264 page

AM1808

SPRS653A – FEBRUARY 2010 – REVISED APRIL 2010

www.ti.com

3.7.19 Multimedia Card/Secure Digital (MMC/SD)

Table 3-21. Multimedia Card/Secure Digital (MMC/SD) Terminal Functions

SIGNAL

POWER

TYPE(1)

PULL(2)

DESCRIPTION

GROUP(3)

NAME

NO.

MMCSD0

MMCSD0_CLK / PRU1_R30[31] /GP4[7] / PRU1_R31[23]

CP[18]

MMCSD0 Clock

EMA_A[22] / MMCSD0_CMD / PRU1_R30[30] / GP4[6] /

A10

I/O

CP[18]

MMCSD0 Command

PRU1_R31[22]

EMA_A[14] / MMCSD0_DAT[7] / PRU1_R30[22] / GP5[14]

A12

I/O

CP[19]

EMA_A[15] / MMCSD0_DAT[6] / PRU1_R30[23] / GP5[15]

C11

I/O

CP[19]

EMA_A[16] / MMCSD0_DAT[5] / PRU1_R30[24] / GP4[0]

E12

I/O

CP[18]

EMA_A[17] / MMCSD0_DAT[4] / PRU1_R30[25] / GP4[1]

B11

I/O

CP[18]

EMA_A[18] / MMCSD0_DAT[3] / PRU1_R30[26] / GP4[2] /

E11

I/O

CP[18]

PRU1_R31[18]

MMC/SD0 data

EMA_A[19] / MMCSD0_DAT[2] / PRU1_R30[27] / GP4[3] /

C10

I/O

CP[18]

PRU1_R31[19]

EMA_A[20] / MMCSD0_DAT[1] / PRU1_R30[28] / GP4[4] /

A11

I/O

CP[18]

PRU1_R31[20]

EMA_A[21] / MMCSD0_DAT[0] / PRU1_R30[29] / GP4[5] /

B10

I/O

CP[18]

PRU1_R31[21]

MMCSD1

PRU0_R30[24] /MMCSD1_CLK / UPP_CHB_START /

CP[30]

MMCSD1 Clock

GP8[14]/PRU1_R31[26]/

PRU0_R30[23] /MMCSD1_CMD / UPP_CHB_ENABLE /

I/O

CP[30]

MMCSD1 Command

GP8[13]/PRU1_R31[25]

MMCSD1_DAT[7] / LCD_PCLK / PRU1_R30[7] / GP8[11]

I/O

CP[31]

MMCSD1_DAT[6] / LCD_MCLK /PRU1_R30[6] / GP8[10] /

I/O

CP[31]

PRU1_R31[7]

MMCSD1_DAT[5] / LCD_HSYNC /PRU1_R30[5] / GP8[9] /

I/O

CP[31]

PRU1_R31[6]

MMCSD1_DAT[4] / LCD_VSYNC /PRU1_R30[4] / GP8[8] /

I/O

CP[31]

PRU1_R31[5]

MMC/SD1 data

VP_CLKIN2 / MMCSD1_DAT[3] / PRU1_R30[3] / GP6[4] /

I/O

CP[30]

PRU1_R31[4]

VP_CLKOUT2 / MMCSD1_DAT[2] / PRU1_R30[2] / GP6[3] /

I/O

CP[30]

PRU1_R31[3]

VP_CLKIN3 / MMCSD1_DAT[1]/ PRU1_R30[1] / GP6[2] /

I/O

CP[30]

PRU1_R31[2]

PRU0_R30[25] / MMCSD1_DAT[0] / UPP_CHB_CLOCK / GP8[15]/

I/O

CP[30]

PRU1_R31[27]

(1)

I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.

Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the signal name

highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured

function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different

types (ie., input versus output), the table reflects the pin function direction for that particular peripheral.

(2)

IPD = Internal Pulldown resistor; IPU = Internal Pullup resistor; CP[n] = configurable pull-up/pull-down (where n is the pin group) using

the PUPDENA and PUPDSEL registers in the System Module. The pull-up and pull-down control of these pins is not active until the

device is out of reset. During reset, all of the pins associated with these registers are weakly pulled down. If the application requires a

pull-up, an external pull-up can be used.

(3)

This signal is part of a dual-voltage IO group (A, B or C). These groups can be operated at 3.3V or 1.8V nominal. The three groups can

be operated at independent voltages but all pins withina group will operate at the same voltage. Group A operates at the voltage of

power supply DVDD3318_A. Group B operates at the voltage of power supply DVDD3318_B. Group C operates at the voltage of power

supply DVDD3318_C.

Device Overview

Submit Documentation Feedback

Product Folder Link(s): AM1808

AM1808AZCE3 bảng dữ liệu(PDF) 44 Page - Texas Instruments

AM1808AZCE3 bảng dữ liệu(HTML) 44 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL