PAM1707BZKB4 datasheet(27/198 Pages) TI

27 / 198 page

AM1707

www.ti.com

SPRS637A – FEBRUARY 2010 – REVISED APRIL 2010

3.6.14

Universal Host-Port Interface (UHPI)

Table 3-16. Universal Host-Port Interface (UHPI) Terminal Functions

No.

SIGNAL NAME

TYPE(1)

PULL(2)

MUXED

DESCRIPTION

ZKB

EMA_D[15]/UHPI_HD[15]/LCD_D[15]/GP0[15]

M16

I/O

IPD

EMA_D[14]/UHPI_HD[14]/LCD_D[14]/GP0[14]

N14

I/O

IPD

EMA_D[13]/UHPI_HD[13]/LCD_D[13]/GP0[13]

N16

I/O

IPD

EMA_D[12]/UHPI_HD[12]/LCD_D[12]/GP0[12]

P14

I/O

IPD

EMIFA, LCD, GPIO

EMA_D[11]/UHPI_HD[11]/LCD_D[11]/GP0[11]

P16

I/O

IPD

EMA_D[10]/UHPI_HD[10]/LCD_D[10]/GP0[10]

R14

I/O

IPD

EMA_D[9]/UHPI_HD[9]/LCD_D[9]/GP0[9]

T14

I/O

IPD

EMA_D[8]/UHPI_HD[8]/LCD_D[8]/GP0[8]

N12

I/O

IPD

EMA_D[7]/MMCSD_DAT[7]/UHPI_HD[7]/GP0[7]/

EMIFA, MMC/SD,

UHPI data bus.

M15

I/O

IPU

BOOT[13]

GPIO, BOOT

EMA_D[6]/MMCSD_DAT[6]/UHPI_HD[6]/GP0[6]

N13

I/O

IPU

EMA_D[5]/MMCSD_DAT[5]/UHPI_HD[5]/GP0[5]

N15

I/O

IPU

EMA_D[4]/MMCSD_DAT[4]/UHPI_HD[4]/GP0[4]

P13

I/O

IPU

EMIFA, MMC/SD,

GPIO

EMA_D[3]/MMCSD_DAT[3]/UHPI_HD[3]/GP0[3]

P15

I/O

IPU

EMA_D[2]/MMCSD_DAT[2]/UHPI_HD[2]/GP0[2]

R13

I/O

IPU

EMA_D[1]/MMCSD_DAT[1]/UHPI_HD[1]/GP0[1]

R15

I/O

IPU

EMA_D[0]/MMCSD_DAT[0]/UHPI_HD[0]/GP0[0]/

EMIFA, MMC/SD,

T13

I/O

IPU

BOOT[12]

GPIO, BOOT

EMA_A[2]/MMCSD_CMD/UHPI_HCNTL1/GP1[2]

I/O

IPU

EMIFA,

MMCSD_CMD,

UHPI access control.

EMA_A[1]/MMCSD_CLK/UHPI_HCNTL0/GP1[1]

I/O

IPU

GPIO

UHPI half-word

EMA_BA[1]/LCD_D[5]/UHPI_HHWIL/GP1[13]

I/O

IPU

EMIFA, LCD, GPIO

identification control.

EMIFA, McASP,

EMA_WE/UHPI_HRW /AXR0[12]/GP2[3]/BOOT[14]

M13

I/O

IPU

UHPI read/write.

GPIO, BOOT

EMIFA, GPIO,

EMA_CS[2]/ UHPI_HCS /GP2[5]/BOOT[15]

I/O

IPU

UHPI chip select.

BOOT

EMA_WE_DQM[1]/ UHPI_HDS2 /AXR0[14]/GP2[8]

P12

I/O

IPU

UHPI data strobe.

EMIFA, McASP0,

EMA_OE/ UHPI_HDS1 /AXR0[13]/GP2[7]

I/O

IPU

GPIO

EMA_WE_DQM[0]/ UHPI_HINT /AXR0[15]/GP2[9]

M14

I/O

IPU

UHPI host interrupt.

EMA_WAIT[0]/ UHPI_HRDY /GP2[10]

I/O

IPU

UHPI ready.

EMIFA, GPIO

UHPI address

EMA_CS[0]/ UHPI_HAS /GP2[4]

I/O

IPU

strobe.

(1)

I = Input, O = Output, I/O = Bidirectional, Z = High impedance, PWR = Supply voltage, GND = Ground, A = Analog signal.

Note: The pin type shown refers to the input, output or high-impedance state of the pin function when configured as the the signal name

highlighted in bold. All multiplexed signals may enter a high-impedance state when the configured function is input-only or the configured

function supports high-Z operation. All GPIO signals can be used as input or output. For multiplexed pins where functions have different

types (ie., input versus output), the table reflects the pin function direction for that particular peripheral.

(2)

IPD = Internal Pulldown resistor, IPU = Internal Pullup resistor

Device Overview

Submit Documentation Feedback

Product Folder Link(s): AM1707

PAM1707BZKB4 bảng dữ liệu(PDF) 27 Page - Texas Instruments

PAM1707BZKB4 bảng dữ liệu(HTML) 27 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL