| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
STM32F100C4H7B bảng dữ liệu(PDF) 67 Page - STMicroelectronics |
|
|
|||||||||||||||||||||||||||||
STM32F100C4H7B bảng dữ liệu(HTML) 67 Page - STMicroelectronics |
|
67 / 84 page ![]() STM32F100x4, STM32F100x6, STM32F100x8, STM32F100xB Electrical characteristics Doc ID 16455 Rev 2 67/84 The above formula (Equation 1) is used to determine the maximum external impedance allowed for an error below 1/4 of LSB. Here N = 12 (from 12-bit resolution). Note: ADC accuracy vs. negative injection current: Injecting a negative current on any of the standard (non-robust) analog input pins should be avoided as this significantly reduces the accuracy of the conversion being performed on another analog input. It is recommended to add a Schottky diode (pin to ground) to standard analog pins which may potentially inject Table 42. RAIN max for fADC = 12 MHz (1) 1. Guaranteed by design, not tested in production. Ts (cycles) tS (µs) RAIN max (k) 1.5 0.125 0.4 7.5 0.625 5.9 13.5 1.125 11.4 28.5 2.375 25.2 41.5 3.45 37.2 55.5 4.625 50 71.5 5.96 NA 239.5 20 NA Table 43. ADC accuracy - limited test conditions(1)(2) 1. ADC DC accuracy values are measured after internal calibration. 2. Based on characterization, not tested in production. Symbol Parameter Test conditions Typ Max Unit ET Total unadjusted error fPCLK2 = 24 MHz, fADC = 12 MHz, RAIN < 10 k, VDDA = 3 V to 3.6 V TA = 25 °C Measurements made after ADC calibration ±1.3 ±2 LSB EO Offset error ±1 ±1.5 EG Gain error ±0.5 ±1.5 ED Differential linearity error ±0.7 ±1 EL Integral linearity error ±0.8 ±1.5 Table 44. ADC accuracy(1) (2) 1. ADC DC accuracy values are measured after internal calibration. 2. Better performance could be achieved in restricted VDD, frequency, VREF and temperature ranges. Symbol Parameter Test conditions Typ Max(3) 3. Based on characterization, not tested in production. Unit ET Total unadjusted error fPCLK2 = 24 MHz, fADC = 12 MHz, RAIN < 10 k, VDDA = 2.4 V to 3.6 V Measurements made after ADC calibration ±2 ±5 LSB EO Offset error ±1.5 ±2.5 EG Gain error ±1.5 ±3 ED Differential linearity error ±1 ±2 EL Integral linearity error ±1.5 ±3 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |