DS1876 datasheet(5/69 Pages) MAXIM

5 / 69 page

_______________________________________________________________________________________ 5

SFP Controller with Dual LDD Interface

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect device reliability.

Voltage Range on PMON_, BMON_, RSEL,

IN1, TXF_, and TXD_ Pins

Relative to Ground ............................... -0.5V to (VCC + 0.5V)*

Voltage Range on VCC, SDA, SCL,

OUT1, RSELOUT, and TXFOUT Pins

Relative to Ground ...............................................-0.5V to +6V

Continuous Power Dissipation

28-Pin TQFN (derate 34.5mW/°C) above +70°C....2758.6mW

Operating Temperature Range.......................... -40NC to +95NC

Programming Temperature Range ....................... 0NC to +95NC

Storage Temperature Range............................ -55NC to +125NC

Soldering Temperature .........................Refer to the IPC/JEDEC

J-STD-020 Specification.

RECOMMENDED OPERATING CONDITIONS

(TA = -40NC to +95NC, unless otherwise noted.)

DC ELECTRICAL CHARACTERISTICS

(VCC = +2.85V to +3.9V, TA = -40NC to +95NC, unless otherwise noted.)

ABSOLUTE MAXIMUM RATINGS

*Subject to not exceeding +6V.

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

Main Supply Voltage

VCC

(Note 1)

+2.85

+3.9

High-Level Input Voltage

(SDA, SCL)

VIH:1

0.7 x

VCC

VCC +

0.3

Low-Level Input Voltage

(SDA, SCL)

VIL:1

-0.3

0.3 x

VCC

High-Level Input Voltage

(TXD_, TXF_, RSEL, IN1)

VIH:2

2.0

VCC +

0.3

Low-Level Input Voltage

(TXD_, TXF_, RSEL, IN1)

VIL:2

-0.3

+0.8

PARAMETER

SYMBOL

CONDITIONS

MIN

TYP

MAX

UNITS

Supply Current

ICC

(Notes 1, 2)

2.5

Output Leakage (SDA, OUT1,

RSELOUT, TXFOUT)

ILO

Low-Level Output Voltage

(SDA, OUT1, RSELOUT,

TXDOUT_, MOD_, APC_,

TXFOUT)

VOL

IOL = 4mA

0.4

IOL = 6mA

0.6

High-Level Output Voltage

(MOD_, APC_, TXDOUT_)

VOH

IOH = 4mA

VCC -

0.4

TXDOUT_ Before EEPROM

Recall

100

MOD_, APC_ Before Recall

Figure 1

100

Input Leakage Current

(SCL, TXD_, RSEL, IN1, TXF_)

ILI

Digital Power-On Reset

POD

1.0

2.2

Analog Power-On Reset

POA

2.0

2.75

DS1876 bảng dữ liệu(PDF) 5 Page - Maxim Integrated Products

DS1876 bảng dữ liệu(HTML) 5 Page - Maxim Integrated Products

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

bảng dữ liệu tải về

Link URL