| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
DM9103 bảng dữ liệu(PDF) 28 Page - Davicom Semiconductor, Inc. |
|
|
|||||||||||||||||||||||||||||
DM9103 bảng dữ liệu(HTML) 28 Page - Davicom Semiconductor, Inc. |
|
28 / 89 page ![]() DM9103 3-port switch with PCI Interface 28 Preliminary datasheet DM9103-DS-P02 September 26, 2007 6.2.7 Network Operation Mode Register (CR6) Bit Name Default Description 31 Reserved 0,RO Must be Zero 30:29 Reserved 0,RO Reserved 28:25 Reserved 0001,RO 0001: normal mode 0011: memory test mode (CR13/14 enable) 24:23 Reserved 00,RO Must be Zero 22 Reserved 0,RO Reserved 21 Reserved 0,RO Reserved 20 Reserved 0,RW Reserved 19 Reserved 0,RW Reserved 18 Reserved 0,RO Reserved 17 MII_CNTL 0,RW MII Management Pin Control Set this bit to enable CR9 bit 16~19 to control MII management pin (MDC,MDIO) 16 1PKT 0,RW One Packet Mode When this bit is set, only one packet is stored at TX FIFO 15:14 Reserved 0,RO Reserved 13 TXSC 0,RW Transmit Start/Stop Command When set, the transmit process will begin by fetching the transmit descriptor for available packet data to be transmitted (running state). If the fetched descriptor is owned by the host, transmit process will enter the suspend state and transmit buffer unavailable (CR5<2>) is set. Otherwise it will begin to move data from host to FIFO and transmit out after reaching threshold value. When reset, the transmit process is placed in the stopped state after completing the transmission of the current frame. 12 Reserved 0,RO Reserved 11:10 LBM 0,RW Loop-back Mode These bits decide two loop-back modes, MAC and PHY, besides normal operation. These loop-back modes expect transmitted data back to receive path and ignore collision detection. Bit11 Bit10 Loop-back Mode 0 0 Normal 0 1 Internal loop-back 1 X Reserved 9 Reserved 0,RO Reserved 8 Reserved 0,RO Must be Zero 7 PAM 0,RW Pass All Multicast When set, any packet with a multicast destination address is received by the DM9103. The packet with a physical address will also be filtered based on the filter mode setting 6 PM 0,RW Promiscuous Mode When set, any incoming valid frame is received by the DM9103, and no matter what the destination address is. The DM9103 is initialized to this mode after reset operation. 5 Reserved 0,RW Must be Zero. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |