ATmega88-15AT datasheet(39/340 Pages) ATMEL

39 / 340 page

7530H–AVR–02/09

ATmega48/88/168 Automotive

7.6

Power Reduction Register

The Power Reduction Register, PRR, provides a method to stop the clock to individual peripher-

als to reduce power consumption. The current state of the peripheral is frozen and the I/O

registers can not be read or written. Resources used by the peripheral when stopping the clock

will remain occupied, hence the peripheral should in most cases be disabled before stopping the

clock. Waking up a module, which is done by clearing the bit in PRR, puts the module in the

same state as before shutdown.

Module shutdown can be used in Idle mode and Active mode to significantly reduce the overall

power consumption. See Section 28.1.1 “Power-Down Supply Current” on page 308 for exam-

ples. In all other sleep modes, the clock is already stopped.

7.6.1

Power Reduction Register - PRR

• Bit 7 - PRTWI: Power Reduction TWI

Writing a logic one to this bit shuts down the TWI by stopping the clock to the module. When

waking up the TWI again, the TWI should be re-initialized to ensure proper operation.

Bit 6 - PRTIM2: Power Reduction Timer/Counter2

Writing a logic one to this bit shuts down the Timer/Counter2 module in synchronous mode (AS2

is 0). When the Timer/Counter2 is enabled, operation will continue like before the shutdown.

• Bit 5 - PRTIM0: Power Reduction Timer/Counter0

Writing a logic one to this bit shuts down the Timer/Counter0 module. When the Timer/Counter0

is enabled, operation will continue like before the shutdown.

• Bit 4 - Res: Reserved bit

This bit is reserved in ATmega48/88/168 and will always read as zero.

• Bit 3 - PRTIM1: Power Reduction Timer/Counter1

Writing a logic one to this bit shuts down the Timer/Counter1 module. When the Timer/Counter1

is enabled, operation will continue like before the shutdown.

• Bit 2 - PRSPI: Power Reduction Serial Peripheral Interface

If using debugWIRE On-chip Debug System, this bit should not be written to one. Writing a logic

one to this bit shuts down the Serial Peripheral Interface by stopping the clock to the module.

When waking up the SPI again, the SPI should be re-initialized to ensure proper operation.

• Bit 1 - PRUSART0: Power Reduction USART0

Writing a logic one to this bit shuts down the USART by stopping the clock to the module. When

waking up the USART again, the USART should be re-initialized to ensure proper operation.

• Bit 0 - PRADC: Power Reduction ADC

Writing a logic one to this bit shuts down the ADC. The ADC must be disabled before shut down.

The analog comparator cannot use the ADC input MUX when the ADC is shut down.

Bit

543

PRTWI

PRTIM2

PRTIM0

–

PRTIM1

PRSPI

PRUSART0

PRADC

PRR

Read/Write

R/W

Initial Value

ATmega88-15AT bảng dữ liệu(PDF) 39 Page - ATMEL Corporation

ATmega88-15AT bảng dữ liệu(HTML) 39 Page - ATMEL Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

bảng dữ liệu tải về

Link URL