| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
PIC18F44J10-I/ML bảng dữ liệu(PDF) 29 Page - Microchip Technology |
|
|
|||||||||||||||||||||||||||||
PIC18F44J10-I/ML bảng dữ liệu(HTML) 29 Page - Microchip Technology |
|
29 / 368 page ![]() © 2009 Microchip Technology Inc. DS39682E-page 27 PIC18F45J10 FAMILY 3.0 OSCILLATOR CONFIGURATIONS 3.1 Oscillator Types The PIC18F45J10 family of devices can be operated in five different oscillator modes: 1. HS High-Speed Crystal/Resonator 2. HSPLL High-Speed Crystal/Resonator with Software PLL Control 3. EC External Clock with FOSC/4 Output 4. ECPLL External Clock with Software PLL Control 5. INTRC Internal 31 kHz Oscillator Four of these are selected by the user by programming the FOSC<2:0> Configuration bits. The fifth mode (INTRC) may be invoked under software control; it can also be configured as the default mode on device Resets. 3.2 Crystal Oscillator/Ceramic Resonators (HS Modes) In HS or HSPLL Oscillator modes, a crystal or ceramic resonator is connected to the OSC1 and OSC2 pins to establish oscillation. Figure 3-1 shows the pin connections. The oscillator design requires the use of a parallel cut crystal. FIGURE 3-1: CRYSTAL/CERAMIC RESONATOR OPERATION (HS OR HSPLL CONFIGURATION) TABLE 3-1: CAPACITOR SELECTION FOR CERAMIC RESONATORS Note: Use of a series cut crystal may give a fre- quency out of the crystal manufacturer’s specifications. Typical Capacitor Values Used: Mode Freq. OSC1 OSC2 HS 8.0 MHz 16.0 MHz 27 pF 22 pF 27 pF 22 pF Capacitor values are for design guidance only. These capacitors were tested with the resonators listed below for basic start-up and operation. These values are not optimized . Different capacitor values may be required to produce acceptable oscillator operation. The user should test the performance of the oscillator over the expected VDD and temperature range for the application. See the notes following Table 3-2 for additional information. Resonators Used: 4.0 MHz 8.0 MHz 16.0 MHz Note 1: See Table 3-1 and Table 3-2 for initial values of C1 and C2. 2: A series resistor (RS) may be required for AT strip cut crystals. 3: RF varies with the oscillator mode chosen. C1(1) C2(1) XTAL OSC2 OSC1 RF(3) Sleep To Logic PIC18F45J10 RS(2) Internal |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |