 |
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
|
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
SPX2940 bảng dữ liệu(PDF) 7 Page - Exar Corporation |
|
|
|||||||||||||||||||||||||||||
SPX2940 bảng dữ liệu(HTML) 7 Page - Exar Corporation |
|
|
7 / 10 page  S SP PX X2 29 94 40 0 1 1A A L Lo ow w D Drro op po ou utt V Vo olltta ag ge e R Re eg gu ulla atto orr © 2009 Exar Corporation 7/10 Rev. 2.0.0 THEORY OF OPERATION The SPX2940 incorporates protection against over-current faults, reversed load insertion, over temperature operation, and positive and negative transient voltage. THERMAL CONSIDERATIONS Although the SPX2940 offers limiting circuitry for overload conditions, it is still necessary to insure that the maximum junction temperature is not exceeded in the application. Heat will flow through the lowest resistance path, the junction-to-case path. In order to insure the best thermal flow of the component, proper mounting is required. Since the case of the device is electrically connected to the output, the case must be electrically isolated using a thermally conductive spacer, which itself contributes some small additional thermal resistance. Consult heatsink manufacturer for thermal resistance and design of heatsink. TO-220 Design Example: Assume that VIN = 10V, VOUT = 5V, IOUT = 1.5A, TA = 50°C/W, θHA= 1°C/W, θCH = 2°C/W, and θJC = 3°C/W. Where TA = ambient temperature θHA = heatsink to ambient thermal resistance θCH = case to heatsink thermal resistance θJC = junction to case thermal resistance The power calculated under these conditions is: PD = (VIN – VOUT) * IOUT = 7.5W. And the junction temperature is calculated as TJ = TA + PD * (θHA + θCH + θJC) or TJ = 50 + 7.5 * (1 + 2 + 3) = 95°C Reliable operation is insured. CAPACITOR REQUIREMENTS The output capacitor is needed to insure stability and minimize the output noise. The value of the capacitor varies with the load. However, a minimum value of 10µF aluminum capacitor will guarantee stability over all load conditions. A tantalum capacitor is recommended if a faster load transient response is needed. If the power source has a high AC impedance, a 0.1µF ceramic capacitor between input & ground is recommended. MINIMUM LOAD CURRENT To ensure a proper behavior of the regulator under light load, a minimum load of 5mA for SPX2940 is required. consequat eu, consequat eu, ullamcorper pretium, magna. Aenean varius turpis sed metus. Donec erat. Nunc urna pede, accumsan sed, tristique non, lobortis sit amet, pede. Fig. 20: Fixed Output Linear Regulator Fig. 21: Ouput Cap ESR vs IOUT Fig. 22: 5.0VOUT PSSR VIN=10V, VOUT=5V COUT=22F, IOUT=10mA |
|
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Vietnamese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
