CX4VCSM1 datasheet(2/2 Pages) RSG

2 / 2 page

RSG Electronic Components GmbH - Sprendlinger Landstr. 115 - 63069 Offenbach - Germany - www.rsg-electronic.de

TEM C

ERTIF

10103 - Rev C

TERMINATIONS

Designation

Termination

SM1

Gold Plated

SM2

Solder Plated

SM3

Solder Dipped

PACKAGING OPTIONS

CX4VSM

- Tray Pack

- 16mm tape, 7” or 13” reels

(Reference tape and reel data sheet 10109)

SPECIFICATIONS

Specifications are typical at 25

OC unless otherwise noted.

Specifications are subject to change without notice.

Parameters

Fundamental

Overtone

Frequency, (kHz)

32.768

100

200

Motional Resistance R1(kΩ)

2.4

Motional Capacitance C1 (fF)

2.3

1.07

2.2

Quality Factor Q (k)

140

Shunt Capacitance C0 (pF)

1.1

0.7

1.2

Load Capacitance (pF)*

Turning Point (

oC)*

Standard Calibration Tolerance**

Glass Lid:

30 ppm

100 ppm

1000 ppm

(0.003%)

(0.01%)

(0.1%)

Ceramic Lid:

100 ppm

1000 ppm

10000 ppm

(0.01%)

(0.1%)

(1.0%)

Drive Level

0.5

µW MAX

Temperature Coefficient (k) -0.035 ppm/

OC2

Note: Frequency f at temperature T is related to frequency f0 at

turning point temperature T0 by:

Aging, first year

5 ppm

Shock, survival

5,000 g peak, 0.3 ms, 1/2 sine

Vibration, survival

20 g RMS, 10-2,000 Hz random

Operating Temp. Range

-10

OC to +70OC (Commercial)

-40

OC to +85OC (Industrial)

-55

OC to +125OC (Military)

Storage Temp. Range

-55

OC to +125OC

Max Process Temperature

260

OC for 20 sec.

* Other values available

** Tighter tolerances available

f-f0

k(T-T0)

HOW TO ORDER CX4VSM CRYSTALS

CX4V

SM1

32.768K , 100

C = Ceramic Lid

Blank = Glass Lid

“S” if special or

custom design.

Blank if standard

SM1 = Gold Plated

SM2 = Solder Plated

SM3 = Solder Dipped

Operating Temp. Range:

C = -10

OC to +70OC

= -40

OC to +85OC

M = -55

OC to +125OC

S = Customer Specified

Frequency

K = kHz

Calibration

Tolerance

@25

(in ppm)

TYPICAL APPLICATION

FOR A PIERCE OSCILLATOR

The CX4 family of surface mount crystals are ideal for

small, high density, battery operated portable products. The

CX4 crystal designed in a Pierce oscillator (single inverter)

circuit provides very low current consumption and high

stability. A conventional CMOS Pierce oscillator circuit is

shown below. The crystal is effectively inductive and in a PI-

network circuit with CD and CG provides the additional

phase shift necessary to sustain oscillation. The oscillation

frequency (f0) is 50 to 150 ppm above the crystal’s series

resonant frequency (fS).

Drive Level

RA is used to limit the crystal’s drive level by forming a

voltage divider between RA and CD. RA also stabilizes the

oscillator against changes in the amplifiers output

resistance (R0). RA should be increased for higher voltage

operation.

Load Capacitance

The CX4 crystal calibration tolerance is influenced by the

effective circuit capacitances, specified as the load

capacitance (CL). CL is approximately equal to:

NOTE: CD and CG include stray layout to ground and CS

is the stray shunt capacitance between the crystal

terminal. In practice, the effective value of CL will be less

than that calculated from CD, CG and CS values because

of the effect of the amplifier output resistance. CS should

be minimized.

The oscillation frequency (f0) is approximately equal to:

AMPLIFIER

BUFFER

CX4

XTAL

OSC

Freq (f )

CONVENTIONAL CMOS

PIERCE OSCILLATOR CIRCUIT

f0 = fS

[1+

]

2(C0 + CL)

(2)

Where f

= Series resonant frequency of the crystal

C1 = Motional Capacitance

C0 = Shunt Capacitance

CL =

CD x CG

CD + CG

(1)

CX4VCSM1 bảng dữ liệu(PDF) 2 Page - RSG Electronic Components GmbH

CX4VCSM1 bảng dữ liệu(HTML) 2 Page - RSG Electronic Components GmbH

Html Pages

1 2

bảng dữ liệu tải về

Link URL