SN74ALVCH16374DLR datasheet(4/14 Pages) TI

4 / 14 page

www.ti.com

ELECTRICAL CHARACTERISTICS

TIMING REQUIREMENTS

SN74ALVCH16374

16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOP

WITH 3-STATE OUTPUTS

SCES021L – JULY 1995 – REVISED SEPTEMBER 2004

over recommended operating free-air temperature range (unless otherwise noted)

PARAMETER

TEST CONDITIONS

VCC

MIN TYP(1)

MAX

UNIT

IOH = -100 µA

1.65 V to 3.6 V

VCC - 0.2

IOH = -4 mA

1.65 V

1.2

IOH = -6 mA

2.3 V

VOH

2.3 V

1.7

IOH = -12 mA

2.7 V

2.2

3 V

2.4

IOH = -24 mA

3 V

IOL = 100 µA

1.65 V to 3.6 V

0.2

IOL = 4 mA

1.65 V

0.45

IOL = 6 mA

2.3 V

0.4

VOL

2.3 V

0.7

IOL = 12 mA

2.7 V

0.4

IOL = 24 mA

3 V

0.55

VI = VCC or GND

3.6 V

±5

µA

VI = 0.58 V

1.65 V

VI = 1.07 V

1.65 V

-25

VI = 0.7 V

2.3 V

II(hold)

VI = 1.7 V

2.3 V

-45

µA

VI = 0.8 V

3 V

VI = 2 V

3 V

-75

VI = 0 to 3.6 V(2)

3.6 V

±500

IOZ

VO = VCC or GND

3.6 V

±10

µA

ICC

VI = VCC or GND,

IO = 0

3.6 V

µA

∆I

One input at VCC - 0.6 V,

Other inputs at VCC or GND

3 V to 3.6 V

750

µA

Control inputs

VI = VCC or GND

3.3 V

Data inputs

Outputs

VO = VCC or GND

3.3 V

(1)

All typical values are at VCC = 3.3 V, TA = 25°C.

(2)

This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to

another.

over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1)

VCC = 2.5 V

VCC = 3.3 V

VCC = 1.8 V

VCC = 2.7 V

± 0.2 V

± 0.3 V

UNIT

MIN

TYP

MIN

MAX

MIN

MAX

MIN

MAX

fclock

Clock frequency

(1)

150

MHz

Pulse duration, CLK high or low

(1)

3.3

tsu

Setup time, data before CLK

↑

(1)

2.1

2.2

1.9

Hold time, data after CLK

↑

(1)

0.6

0.5

(1)

This information was not available at the time of publication.

SN74ALVCH16374DLR bảng dữ liệu(PDF) 4 Page - Texas Instruments

SN74ALVCH16374DLR bảng dữ liệu(HTML) 4 Page - Texas Instruments

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14

bảng dữ liệu tải về

Link URL