AD23601C datasheet(2/2 Pages) MPD

2 / 2 page

Derating Curve

Model Selection Guide

Mechanical Dimensions

Notes:

• All dimensions are typical in inches (mm)

• Tolerance x.xx = ±0.01 (±0.25)

MicroPower Direct

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com

Model

Number

Rated

Power

(W)

Input

Output

Overvoltage

Protection

(VDC)

Ripple &

Noise

(mV p-p)

Efﬁciency

(%, Typ)

Voltage (VAC)

Current (A)

Voltage

(VDC)

Current (A)

Max)

Current (A)

Range

Universal Range 115 VAC 230 VAC

AD23601C

360

100 - 240

1.0

0.5

+12 (V1)

28.0

0 ~ 28.0

14 ~ 16

100

+5 (V2)

3.0

0 ~ 3.0

N/A

AD23602C

360

100 - 240

1.0

0.5

+24 (V1)

14.0

0 ~ 14.0

27 ~ 30

150

+5 (V2)

3.0

0 ~ 3.0

N/A

AD23603C

360

100 - 240

1.0

0.5

48 (V1)

7.0

0 ~ 7.0

52 ~ 56

250

+5 (V2)

3.0

0 ~ 3.0

N/A

Notes:

1. Load regulation is speciﬁed for a load change

of 20% to 100%. For models AD23601C, load

regulation for V1 (12V) is ±2%

2. Ripple & noise is measured using equipment with

20 Mhz of bandwidth with the unit under test

operating at rated load and a 110 VAC input.

Connection to the unit is made with a 0.1 μF /

630V metalized capacitor & a 47 μF electrolytic

capacitor connected in parallel.

3. Transient recovery is measured to within a 1%

error band for a load step change of 50% to

100%.

4. Isolation resistance is given for Input/Output and

Input/FG. For Output/FG., it is 50 M

5. Overload protection is power limiting. The

unit recovers automatically when the fault is

removed.

6. Over voltage protection is a shut down type.

The unit recovers automatically when the fault

is removed.

7. To mount the unit to the DIN rail, tilt the unit

rearwards from the top, ﬁtting the mount over

the top of the rail. Press back on the bottom front

of the unit until it locks in place on the rail. To

remove the unit from the rail, pull the removal

clip at the bottom rear of the unit downward

with a screw driver. With the clip down, lift up

on the unit from the bottom front until it clears

the rail. Before installation or removal all wiring

should be disconnected and the main power to

the system shut off.

8. When wiring the supply, all lines should be as

thick and short as possible. AWG 14 wire is recom-

mended for the AD2360C series.

9. The units should be mounted so they are vertically

orientated. Air ﬂow (if provided) would optimally

ﬂow from the bottom to the top of the unit.

10. It is recommended that a fuse be used on the

input of a power supply for protection. For

the AD2360C series a 250VAC 5.0A is recom-

mended.

Connections TB 1

Function

FT (Optional)

3+V2 (5V) Output

Output Common

6+V1 Output

7+V1 Output

Connections TB 2

Function

AC Input - Live

AC Input - Neutral

Frame Ground (FG

Units with the optional “FT” outputs may be

easily connected for “Fault Tolerant operation.

Contact the factory for details

AD23601C bảng dữ liệu(PDF) 2 Page - MicroPower Direct, LLC

AD23601C bảng dữ liệu(HTML) 2 Page - MicroPower Direct, LLC

Html Pages

1 2

bảng dữ liệu tải về

Link URL