CDC351

1-LINE TO 10-LINE CLOCK DRIVER

WITH 3-STATE OUTPUTS

SCAS441C – FEBUARY 1994 – REVISED NOVEMBER 1995

3

POST OFFICE BOX 655303

– 0.5 V to 4.6 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 0.5 V to 7 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Voltage range applied to any output in the high state or power-off state,

– 0.5 V to 3.6 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

64 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

–18 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 50 mA

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

0.65 W

. . . . . . . . . . . . . . . . .

DW package

1.7 W

. . . . . . . . . . . . . . . . .

– 65 to 150

°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not

implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES:

1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed.

2. The maximum package power dissipation is calculated using a junction temperature of 150

°C and a board trace length of 750 mils.

For more information, refer to the

Package Thermal Considerations application note in the 1994 ABT Advanced BiCMOS Technology

Data Book, literature number SCBD002B.

recommended operating conditions (see Note 3)

MIN

MAX

UNIT

VCC

Supply voltage

3

3.6

V

VIH

High-level input voltage

2

V

VIL

Low-level input voltage

0.8

V

VI

Input voltage

0

5.5

V

IOH

High-level output current

–32

mA

IOL

Low-level output current

32

mA

fclock

Input clock frequency

100

MHz

TA

Operating free-air temperature

0

70

°C

NOTE 3: Unused pins (input or I/O) must be held high or low.

electrical characteristics over recommended operating free-air temperature range (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

PARAMETER

TEST CONDITIONS

MIN

TYP

MAX

UNIT

VIK

VCC = 3 V,

II = –18 mA

–1.2

V

VOH

VCC = 3 V,

IOH = – 32 mA

2

V

VOL

VCC = 3 V,

IOL = 32 mA

0.5

V

II

VCC = 3.6 V,

VI = VCC or GND

±1

µA

IO‡

VCC = 3.6 V,

VO = 2.5 V

–15

–150

mA

IOZ

VCC = 3.6 V,

VO = 3 V or 0

±10

µA

V3 6 V

I

0

Outputs high

0.3

ICC

VCC = 3.6 V,

IO = 0,

VI =VCC or GND

Outputs low

25

mA

VI = VCC or GND

Outputs disabled

0.3

Ci

VI = VCC or GND,

VCC = 3.3 V,

f = 10 MHz

4

pF

Co

VO = VCC or GND,

VCC = 3.3 V,

f = 10 MHz

6

pF

‡ Not more than one output should be tested at a time, and the duration of the test should not exceed one second.