HV830 datasheet(4/4 Pages) SUTEX

4 / 4 page

Figure 3: Split Supply Configuration

*Larger values may be required depending upon supply impedance.

For additional information, see Application Notes AN-H33 and AN-H34.

External Component Description

External Component

Selection Guide Line

Diode

Fast reverse recovery diode, BAS21LT1 or equivalent.

Cs Capacitor

0.01

µF to 0.1µF, 200V capacitor to GND is used to store the energy transferred from the inductor.

EL-osc

The EL lamp frequency is controlled via an external R

EL resistor connected between REL-osc and VDD of the

device. The lamp frequency increases as R

EL decreases. As the EL lamp frequency increases, the amount

of current drawn from the battery will increase and the output voltage V

CS will decrease. The color of the EL

lamp is dependent upon its frequency.

A 3.3M

Ω resistor would provide lamp frequency of 220 to 280Hz. Decreasing the R

EL-osc by a factor of 2 will

increase the lamp frequency by a factor of 2.

SW-osc

The switching frequency of the converter is controlled via an external resistor, R

SW between RSW-osc and VDD

of the device. The switching frequency increases as R

SW decreases. With a given inductor, as the switching

frequency increases, the amount of current drawn from the battery will decrease and the output voltage, V

CS,

will also decrease.

SW Capacitor

A 1nF capacitor is recommended on R

SW-osc to GND when a 0.01µF CS capacitor is used. This capacitor

is used to shunt any switching noise that may couple into the R

SW-osc pin. The CSW capacitor may also be

needed when driving large EL lamp due to an increase in switching noise.

Lx Inductor

The inductor L

x is used to boost the low input voltage by inductive flyback. When the internal switch is on,

the inductor is being charged. When the internal switch is off, the charge stored in the inductor will be

transferred to the high voltage capacitor C

S. The energy stored in the capacitor is connected to the internal

H-bridge and therefore to the EL lamp. In general, smaller value inductors, which can handle more current,

are more suitable to drive larger size lamps. As the inductor value decreases, the switching frequency of the

inductor (controlled by R

SW) should be increased to avoid saturation.

220

µH Murata inductors with 5.4Ω series DC resistance is typically recommended. For inductors with the

same inductance value but with lower series DC resistance, lower R

SW value is needed to prevent high current

draw and inductor saturation.

Lamp

As the EL lamp size increases, more current will be drawn from the battery to maintain high voltage across

the EL lamp. The input power, (V

IN x IIN), will also increase. If the input power is greater than the power

dissipation of the package (400mW), an external resistor in series with one side of the lamp is recommended

to help reduce the package power dissipation.

VIN = Battery

Voltage

VDD = Regulated

Voltage

ON = VDD

OFF = 0V

200V

0.1

µF*

BAS21LT1

RSW

REL

EL Lamp

HV830LG

GND

REL-osc

VDD

RSW-osc

–

Remote

Enable

1nF

HV830

1235 Bordeaux Drive, Sunnyvale, CA 94089

TEL: (408) 744-0100 • FAX: (408) 222-4895

www.supertex.com

11/12/01

HV830 bảng dữ liệu(PDF) 4 Page - Supertex, Inc

HV830 bảng dữ liệu(HTML) 4 Page - Supertex, Inc

Html Pages

1 2 3 4

bảng dữ liệu tải về

Link URL