| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ATSAM3308B bảng dữ liệu(PDF) 9 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
ATSAM3308B bảng dữ liệu(HTML) 9 Page - ATMEL Corporation |
|
9 / 27 page ![]() 9 6090D–DRMSD–12-Feb-07 ATSAM3308B WD15 – WD0 94, 93, 92, 89, 88, 86, 85, 84, 80, 79, 78, 69, 68, 63, 62, 61 I/O 17 External memory data P3.15 – P3.0 94, 93, 92, 89, 88, 86, 85, 84, 80, 79, 78, 69, 68, 63, 62, 61 I/O 17 General-purpose I/O pins WCS1 3 Out 18 External memory chip select 1, active low. Pre-decode for an external RAM/Flash/ROM at address 200:0000H. P1.10 3 I/O 18 General-purpose I/O pin WCS0 4 Out 19 External memory chip select 2, active low. Pre-decode for an external RAM/Flash/ROM at address 000:0000H P1.9 4 I/O 19 General-purpose I/O pin WOE 48 Out 20 External memory output enable, active low P1.8 48 I/O 20 General-purpose I/O pin WWE 49 Out 21 External memory write enable, active low P1.7 49 I/O 21 General-purpose I/O pin DFCS 23 Out - DataFlash chip select DFSI 25 Out - DataFlash serial input (to DataFlash) DFSO 32 In Pd - DataFlash serial output (from DataFlash). This pin has a built-in pull- down. It may be left open if not used. DFSCK 24 Out - DataFlash data clock P1.15 46 I/O Pu - General-purpose I/O pin. This pin has built-in pull-up. It may be left open if not used. X1 – X2 72,71 - - External crystal connection. Standard frequencies are 6.9552 MHz, 9.6 MHz, 11.2896 MHz, 12.288 MHz. Max frequency is 12.5 MHz. An external clock (max. 1.8 V PP) can be connected to X1 using AC coupling (22 pF). A built-in PLL multiplies the clock frequency by 4 for internal use. LFT 74 - - PLL decoupling RCR filter RESET 33 In - Master reset Schmitt trigger input, active low. RESET should be held low during at least 10 ms after power is applied. On the rising edge of RESET, the chip enters an initialization routine, which may involve firmware download from an external SmartMedia, DataFlash or host. STIN 34 In Pd - Serial test input. This is a 57.6 Kbaud asynchronous input used for firmware debugging. This pin is tested at power-up. The built-in debugger starts if STIN is found high. STIN has a built-in pull-down. It should be grounded or left open for normal operation. Table 6-1. Pinout by Pin Name (Continued) Pin Name Pin Number Type Sharing Description |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |