 |
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
|
công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
ATA5428-PLSW bảng dữ liệu(PDF) 80 Page - ATMEL Corporation |
|
|
|||||||||||||||||||||||||||||
ATA5428-PLSW bảng dữ liệu(HTML) 80 Page - ATMEL Corporation |
|
|
80 / 100 page  80 4841D–WIRE–10/07 ATA5423/ATA5425/ATA5428/ATA5429 5 Synthesizer 5.1 Spurious TX mode At ±f CLK, CLK enabled fRF = 315 MHz f RF = 345 MHz f RF = 433.92 MHz fRF = 868.3 MHz f RF = 915 MHz SPTX –72 –74 –68 –70 –69 dBC C At ±f XTO f RF = 315 MHz fRF = 345 MHz f RF = 433.92 MHz f RF = 868.3 MHz fRF = 915 MHz SP TX –70 –68 –66 –60 –60 dBC C 5.2 Spurious RX mode At ±fCLK, CLK enabled f RF = 315 MHz f RF = 345 MHz fRF = 433.92 MHz f RF = 868.3 MHz f RF = 915 MHz SP RX < –75 < –75 < –75 < –75 < –75 dBC C At ±fXTO fRF = 315 MHz f RF = 345 MHz fRF = 433.92 MHz fRF = 868.3 MHz f RF = 915 MHz SPRX –75 –73 –75 –68 –67 dBC C 5.3 In loop phase noise TX mode Measured at 20 kHz distance to carrier fRF = 315 MHz f RF = 345 MHz fRF = 433.92 MHz fRF = 868.3 MHz f RF = 915 MHz L TX20k –85 –85 –80 –75 –75 dBC/Hz A 5.4 Phase noise at 1M RX mode f RF = 315 MHz fRF = 345 MHz fRF = 433.92 MHz f RF = 868.3 MHz fRF = 915 MHz LRX1M –121 –120 –120 –113 –113 dBC/Hz C 5.5 Phase noise at 1M TX mode fRF = 315 MHz fRF = 345 MHz f RF = 433.92 MHz fRF = 868.3 MHz f RF = 915 MHz L TX1M –113 –113 –111 –107 –107 dBC/Hz C 12. Electrical Characteristics: General (Continued) This device is manufactured with an industrial (not automotive) grade process and process controls. Although this device may meet certain automotive grade criteria in performance, Atmel can not recommend that this device be used in any automotive application. All parameters refer to GND and are valid for Tamb = 25°C, VVS1 = VVS2 = 3.0V (1-battery application), VVS2 = 6.0V (2-battery application) and VVS2 = VVAUX = 5.0V (Base-station Application). Typical values are given at fRF = 433.92 MHz unless otherwise specified. Details about current consumption, timing and digital pin properties can be found in the specific sections of the “Electrical Characteristics”. No. Parameters Test Conditions Pin(1) Symbol Min. Typ. Max. Unit Type* *) Type means: A = 100% tested, B = 100% correlation tested, C = Characterized on samples, D = Design parameter Note: 1. Pin numbers in brackets mean they were measured with RF_IN matched to 50 Ω according to Figure 3-1 on page 11 with component values according to Table 3-2 on page 12 and RF_OUT matched to 50 Ω according to Figure 3-10 on page 21 with component values according to Table 3-7 on page 22. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Vietnamese ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
