| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2111B bảng dữ liệu(PDF) 502 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2111B bảng dữ liệu(HTML) 502 Page - Renesas Technology Corp |
|
502 / 582 page ![]() Rev. 1.00, 05/04, page 468 of 544 20.2 Mode Transitions and LSI States Figure 20.1 shows the enabled mode transition diagram. The mode transition from program execution state to program halt state is performed by the SLEEP instruction. The mode transition from program halt state to program execution state is performed by an interrupt. The STBY input causes a mode transition from any state to hardware standby mode. The RES input causes a mode transition from a state other than hardware standby mode to the reset state. Table 20.2 shows the LSI internal states in each operating mode. Program halt state Program execution state SCK2 to SCK0 are 0 SCK2 to SCK0 are not 0 SLEEP instruction SSBY = 1, PSS = 1, DTON = 1, LSON = 1 Clock switching exception handling SLEEP instruction SSBY = 1, PSS = 1, DTON = 1, LSON = 0 After the oscillation stabilization time (STS2 to STS0), clock switching exception handling SLEEP instruction SLEEP instruction External interrupt *3 Any interrupt SLEEP instruction SLEEP instruction SLEEP instruction Interrupt *1 LSON bit = 0 Interrupt *2 Interrupt *1 LSON bit = 1 STBY pin = High RES pin = Low STBY pin = Low SSBY = 0, LSON = 0 SSBY = 1, PSS = 0, LSON = 0 SSBY = 0, PSS = 1, LSON = 1 SSBY = 1, PSS = 1, DTON = 0 RES pin = High : Transition after exception processing : Power-down mode Reset state High-speed mode (main clock) Medium-speed mode (main clock) Subactive mode (subclock) Subsleep mode (subclock) Hardware standby mode Software standby mode Sleep mode (main clock) Watch mode (subclock) Notes: 1. 2. 3. NMI, IRQ0 to IRQ2, IRQ6, IRQ7, and WDT1 interrupts NMI, IRQ0 to IRQ7, WDT0, WDT1, TMR0, and TMR1 interrupts NMI, IRQ0 to IRQ2, IRQ6, and IRQ7 interrupts • When a transition is made between modes by means of an interrupt, the transition cannot be made on interrupt source generation alone. Ensure that interrupt handling is performed after accepting the interrupt request. • Always select high-speed mode before making a transition to watch mode or sub-active mode. Figure 20.1 Mode Transition Diagram |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |