| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2111B bảng dữ liệu(PDF) 481 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2111B bảng dữ liệu(HTML) 481 Page - Renesas Technology Corp |
|
481 / 582 page ![]() Rev. 1.00, 05/04, page 447 of 544 START End of programming Set SWE bit in FLMCR1 Start of programming Write pulse application subroutine Wait (x) µs Sub-Routine Write Pulse End Sub Set PSU bit in FLMCR2 WDT enable Disable WDT Number of Writes n 1 2 3 4 5 6 7 8 9 10 11 12 13 998 999 1000 Note 7: Write Pulse Width Write Time (z) µs z1 z1 z1 z1 z1 z1 z2 z2 z2 z2 z2 z2 z2 z2 z2 z2 Wait ( γ) µs Set P bit in FLMCR1 Wait (z1) µs, (z2) µs or (z3) µs Clear P bit in FLMCR1 Wait ( α) µs Clear PSU bit in FLMCR2 Wait ( β) µs n = 1 m = 0 NG NG NG NG NG OK OK OK Wait ( γ) µs Wait ( ε) µs *2 *4 *5 *1 Wait ( η) µs Apply write pulse z1 µs or z2 µs Sub-Routine-Call Set PV bit in FLMCR1 H'FF dummy write to verify address Read verify data Write data = verify data? *4 *3 *3 *1 Transfer reprogram data to reprogram data area Reprogram data computation *4 Transfer additional-programming data to additional-programming data area Additional-programming data computation Clear PV bit in FLMCR1 Clear SWE bit in FLMCR1 m = 1 See Note 7 for pulse width m = 0 ? Increment address Programming failure OK Clear SWE bit in FLMCR1 Wait ( θ) µs µs OK 6 ≥ n? NG OK 6 ≥ n ? Wait ( θ) µs n ≥ (N)? n ← n + 1 Original Data (D) Verify Data (V) Reprogram Data (X) Comments Programming completed Still in erased state; no action Programming incomplete; reprogram Note: Use a z3 µs write pulse for additional programming. Write 128-byte data in RAM reprogram data area consecutively to flash memory RAM Program data storage area (128 bytes) Reprogram data storage area (128 bytes) Additional-programming data storage area (128 bytes) Store 128-byte program data in program data area and reprogram data area Apply write pulse (Additional programming) 128-byte data verification completed? Successively write 128-byte data from additional- programming data area in RAM to flash memory Reprogram Data Computation Table Reprogram Data (X') Verify Data (V) Additional- Programming Data (Y) 1 1 1 1 0 1 0 0 0 0 1 1 Comments Additional programming to be executed Additional programming not to be executed Additional programming not to be executed 0 1 1 1 0 1 0 1 0 0 1 1 Additional-Programming Data Computation Table Perform programming in the erased state. Do not perform additional programming on previously programmed addresses. Notes: 1. Data transfer is performed by byte transfer. The lower 8 bits of the first address written to must be H'00 or H'80. A 128-byte data transfer must be performed even if writing fewer than 128 bytes; in this case, H'FF data must be written to the extra addresses. 2. Verify data is read in 16-bit (word) units. 3. Even bits for which programming has been completed will be subjected to programming once again if the result of the subsequent verify operation is NG. 4. A 128-byte area for storing program data, a 128-byte area for storing reprogram data, and a 128-byte area for storing additional data must be provided in RAM. The contents of the reprogram data area and additional data area are modified as programming proceeds. 5. A write pulse of z1 µs or z2 µs is applied according to the progress of the programming operation. See Note7 for details of the pulse widths. When writing of additional-programming data is executed, a z3 µs write pulse should be applied. Reprogram data X' means reprogram data when the write pulse is applied. 6. The values of x, y, z1, z2, z3, α, β, γ, ε, η, θ, and N are shown in section 22.5, Flash Memory Characteristics. Figure 18.9 Program/Program-Verify Flowchart |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |