| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2111B bảng dữ liệu(PDF) 371 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2111B bảng dữ liệu(HTML) 371 Page - Renesas Technology Corp |
|
371 / 582 page ![]() Rev. 1.00, 05/04, page 337 of 544 13.6 Usage Notes 1. In master mode, if an instruction to generate a start condition is issued and then an instruction to generate a stop condition is issued before the start condition is output to the I 2C bus, neither condition will be output correctly. To output the start condition followed by the stop condition, after issuing the instruction that generates the start condition, read DR in each I 2C bus output pin, and check that SCL and SDA are both low. The pin states can be monitored by reading DR even if the ICE bit is set to 1. Then issue the instruction that generates the stop condition. Note that SCL may not yet have gone low when BBSY is cleared to 0. 2. Either of the following two conditions will start the next transfer. Pay attention to these conditions when accessing to ICDR. Write to ICDR when ICE = 1 and TRS = 1 (including automatic transfer from ICDRT to ICDRS) Read from ICDR when ICE = 1 and TRS = 0 (including automatic transfer from ICDRS to ICDRR) 3. Table 13.8 shows the timing of SCL and SDA outputs in synchronization with the internal clock. Timings on the bus are determined by the rise and fall times of signals affected by the bus load capacitance, series resistance, and parallel resistance. Table 13.8 I 2C Bus Timing (SCL and SDA Outputs) Item Symbol Output Timing Unit Notes SCL output cycle time t SCLO 28t cyc to 256tcyc ns SCL output high pulse width t SCLHO 0.5t SCLO ns SCL output low pulse width t SCLLO 0.5t SCLO ns SDA output bus free time t BUFO 0.5t SCLO – 1tcyc ns Start condition output hold time t STAHO 0.5t SCLO – 1tcyc ns Retransmission start condition output setup time t STASO 1t SCLO ns Stop condition output setup time t STOSO 0.5t SCLO + 2tcyc ns Data output setup time (master) 1t SCLLO – 3tcyc Data output setup time (slave) t SDASO 1t SCLL – (6tcyc or 12tcyc*) ns Data output hold time t SDAHO 3t cyc ns See figure 22.22. Note: * 6t cyc when IICX is 0, 12tcyc when 1. 4. SCL and SDA inputs are sampled in synchronization with the internal clock. The AC timing therefore depends on the system clock cycle t cyc, as shown in section 22, Electrical Characteristics. Note that the I 2C bus interface AC timing specifications will not be met with a system clock frequency of less than 5 MHz. |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |