công cụ tìm kiếm bảng dữ liệu linh kiện điện tử
  Vietnamese  ▼
ALLDATASHEET.VN

X  

H8S/20103 bảng dữ liệu(PDF) 241 Page - Renesas Technology Corp

tên linh kiện H8S/20103
Giải thích chi tiết về linh kiện  16-Bit Single-Chip Microcomputer H8S Family / H8S/Tiny Series
PDF  992 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
nhà sản xuất  RENESAS [Renesas Technology Corp]
Trang chủ  http://www.renesas.com
Logo RENESAS - Renesas Technology Corp

H8S/20103 bảng dữ liệu(HTML) 241 Page - Renesas Technology Corp

Back Button H8S/20103 Datasheet HTML 237Page - Renesas Technology Corp H8S/20103 Datasheet HTML 238Page - Renesas Technology Corp H8S/20103 Datasheet HTML 239Page - Renesas Technology Corp H8S/20103 Datasheet HTML 240Page - Renesas Technology Corp H8S/20103 Datasheet HTML 241Page - Renesas Technology Corp H8S/20103 Datasheet HTML 242Page - Renesas Technology Corp H8S/20103 Datasheet HTML 243Page - Renesas Technology Corp H8S/20103 Datasheet HTML 244Page - Renesas Technology Corp H8S/20103 Datasheet HTML 245Page - Renesas Technology Corp Next Button
Zoom Inzoom in Zoom Outzoom out
 241 / 992 page
background image
Section 7 ROM
Rev. 1.00 Oct. 03, 2008 Page 215 of 962
REJ09B0465-0100
(3) Programming
A program command is used to program data in the flash memory in 4-byte units.
Command or data size can be set depending on the FMWUS bit in FLMCR1. Setting the FMWUS
bit to 0 enables using byte instructions. When H'41 is written in the first command cycle and data
is written to the programming address in the second through fifth command cycles, programming
and verifying are automatically started*.
Setting the FMWUS bit to 1 enables using word instructions. When H'4141 is written in the first
command cycle and data is written to the programming address in the second and third command
cycles, programming and verifying are started*.
Completion of programming is indicated by the FMRDY bit in FLMSTR. The FMRDY bit is read
as 0 during programming, and read as 1 after programming completion.
After programming completion, the programming result can be checked by reading the FMPRSF
bit in FLMSTR. (See the description in (9) below, Full Status Checking.)
Figure 7.16 shows the programming flowchart.
Do not additionally program the already-programmed addresses.
Note that if the lock bit is 0 (locked) in the specified block and the FMLBD bit is 0 (lock bit
enabled), a programming command is not accepted for the specified block.
In EW1 mode, do not execute this command for the block in which the reprogramming-control
program is located.
The FMRDY bit in FLMSTR changes to 0 when programming is started, and changes to 1 when
completed.
Note: * The lower two bits of the programming addresses are ignored.



Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100  ...More


bảng dữ liệu tải về

Go To PDF Page


Link URL



Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không?  [ DONATE ] 

Alldatasheet là   |   Quảng cáo   |   Liên lạc với chúng tôi   |   Chính sách bảo mật   |   Liên kết đến bảng dữ liệu    |   Trao đổi link   |   Tìm kiếm theo nhà sản xuất
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com