| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/20103 bảng dữ liệu(PDF) 439 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/20103 bảng dữ liệu(HTML) 439 Page - Renesas Technology Corp |
|
439 / 992 page ![]() Section 13 Timer RA Rev. 1.00 Oct. 03, 2008 Page 413 of 962 REJ09B0465-0100 Timer RA prescaler underflow signal 1. 2. 3. 4. 5. 6. When TRATR is read in pulse cycle measurement mode, the value in the read buffer can be read. The TEDGF bit in TRACR is set to 1 (valid edge exists) on the second underflow of the timer RA prescaler after a valid edge of the measurement pulses is input. TRATR should be read between the TEDGF bit setting to 1 (valid edge exists) and the next valid edge input. The value in the read buffer is retained until TRATR is read. Therefore, if the value is not read before the next valid edge input, the measurement result of the previous cycle remains. The MOV instruction should be used to write 0 to the TEDGF bit in TRACR using a program. Here, 1 should be written to the TUNDF bit . The MOV instruction should be used to write 0 to the TUNDF bit in TRACR using a program. Here, 1 should be written to the TEDGF bit. If an underflow of timer RA and reloading of timer RA by valid edge input occur at the same time, both the TUNDF and TEDGF bits are set to 1. In this case, the effectiveness of the TUNDF bit should be determined according to the read buffer contents. H'0E H'0D H'0F H'0E H'0D H'0C H'0B H'0A H'09 H'0F H'0E H'0D H'01 H'00 H'0F H'0E H'0F H'0D H'0F H'0B H'0A H'0D H'01 H'00 H'0F H'0E H'09 TSTART in TRACR TEDGF in TRACR "1" "0" "1" "0" "1" "0" "1" "0" "1" "0" Measurement pulse (TRAIO pin input) TRATR content Read buffer content *1 TUNDF in TRACR TRAIF in TRAIR Start counting TRA read ( *3) Retained Set to 0 by a program. *4 *2 *2 Set to 0 by a program. *5 *6 Set to 0 by a program. Measurement condition: H'0E TRA reload TRA reload Retained Underflow Set to 1 by a program. The initial value of TRATR is H'0F and the width from the rising edge to the next rising edge of measurement pulse is measured (TEDGSEL = 0). Notes: Figure 13.4 Operation Example of Pulse Cycle Measurement Mode |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |