| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2463 bảng dữ liệu(PDF) 934 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2463 bảng dữ liệu(HTML) 934 Page - Renesas Technology Corp |
|
934 / 1250 page ![]() Section 22 USB Function Module (USB) Rev. 2.00 Aug. 20, 2008 Page 886 of 1198 REJ09B0403-0200 22.8.3 DTC Transfer for Endpoint 2 When the transmit data at EP2 is transferred by the DTC, the USB function module automatically performs the same processing as writing 1 to the PKTE bit in TRG if the currently selected FIFO (64 bytes) becomes full. Accordingly, to transfer data of a multiple of 64 bytes, the user need not write 1 to the PKTE bit. To transfer data of less than 64 bytes, the user must write 1 to the PKTE bit on a DTC transfer end interrupt. If the user writes 1 to the PKTE bit when the maximum number of bytes (64 bytes) are transferred, correct operation cannot be guaranteed. To end the DTC transfer, write 0 to the EP2EMPTY bit in IFR0, after clearing the EP2DMAE bit in DMA to 0 within the processing routine for a DTC transfer end interrupt. If this procedure is omitted, the DTC transfer end interrupt is not cleared. To perform the DTC transfer again, in addition to the said procedure, set the number of transfers, set the DTCERF register, and then set the EP2DMAE bit in DMA to 1. Figure 22.21 shows an example for transmitting 150 bytes of data to the host. In this case, internal processing which is the same as writing 1 to the PKTE bit in TRG is automatically performed twice. This internal processing is performed when the currently selected data FIFO becomes full. Accordingly, this processing is automatically performed only when 64-byte data is sent. When the last 22 bytes are sent, the internal processing for writing 1 to the PKTE bit is not performed, and the user must write 1 to the PKTE bit by software. In this case, the application has no more data to transfer but the USB function module continues to output DTC requests for EP2 as long as the FIFO has an empty space. Therefore, when all data has been transferred, write 0 to the EP2DMAE bit in DMA to cancel DTC transfer requests, and then write 0 to the EP2EMPTY bit in IFR0 to clear the request for a DTC transfer end interrupt. PKTE (Automatically performed) PKTE (Automatically performed) PKTE is not performed Execute by DMA transfer end interrupt (user) 64 bytes 64 bytes 22 bytes Figure 22.21 PKTE Bit Operation for EP2 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |