| công cụ tìm kiếm bảng dữ liệu linh kiện điện tử |
|
H8S/2463 bảng dữ liệu(PDF) 45 Page - Renesas Technology Corp |
|
|
|||||||||||||||||||||||||||||
H8S/2463 bảng dữ liệu(HTML) 45 Page - Renesas Technology Corp |
|
45 / 1250 page ![]() Rev. 2.00 Aug. 20, 2008 Page xlv of xlviii Table 19.2 LADR1, LADR2 Initial Values ............................................................................... 686 Table 19.3 Host Register Selection ............................................................................................ 687 Table 19.4 Slave Selection Internal Registers............................................................................ 687 Table 19.5 LPC I/O Cycle.......................................................................................................... 736 Table 19.6 GA20 Setting/Clearing Timing ................................................................................ 742 Table 19.7 Fast Gate A20 Output Signals.................................................................................. 744 Table 19.8 Scope of LPC Interface Pin Shutdown..................................................................... 746 Table 19.9 Scope of Initialization in Each LPC interface Mode................................................ 747 Table 19.10 Serialized Interrupt Transfer Cycle Frame Configuration...................................... 750 Table 19.11 Receive Complete Interrupts and Error Interrupt................................................... 752 Table 19.12 HIRQ Setting and Clearing Conditions when LPC Channels are Used ................. 754 Table 19.13 HIRQ Setting and Clearing Conditions when SCIF Channels are Used ................ 755 Table 19.14 Host Address Example ........................................................................................... 757 Section 20 Ethernet Controller (EtherC) Table 20.1 Pin Configuration ..................................................................................................... 761 Section 22 USB Function Module (USB) Table 22.1 Pin Configuration ..................................................................................................... 834 Table 22.2 Example of Limitations for Setting Values .............................................................. 858 Table 22.3 Example of Setting................................................................................................... 859 Table 22.4 Relationship between TRNTREG0 Setting and Pin Output..................................... 861 Table 22.5 Relationship between Pin Input and TRNTREG1 Monitoring Value ...................... 862 Table 22.6 Interrupt Sources ...................................................................................................... 863 Table 22.7 Command Decoding on Application Side................................................................ 882 Table 22.8 Selection of Peripheral Module Clock ( φ) when USB Connection is Made ............894 Section 23 A/D Converter Table 23.1 Pin Configuration ..................................................................................................... 897 Table 23.2 Analog Input Channels and Corresponding ADDR Registers ................................. 899 Table 23.3 A/D Conversion Characteristics (Single Mode)....................................................... 907 Table 23.4 A/D Conversion Characteristics (Scan Mode) ......................................................... 907 Table 23.5 A/D Converter Interrupt Source............................................................................... 909 Table 23.6 Standard of Analog Pins........................................................................................... 913 Section 25 Flash Memory Table 25.1 Comparison of Programming Modes ....................................................................... 920 Table 25.2 Pin Configuration ..................................................................................................... 925 Table 25.3 Register/Parameter and Target Mode....................................................................... 927 Table 25.4 Parameters and Target Modes .................................................................................. 937 Table 25.5 Setting On-Board Programming Mode .................................................................... 947 Table 25.6 System Clock Frequency for Automatic-Bit-Rate Adjustment by This LSI ............ 949 |
|
Link URL |
| Cho đến nay ALLDATASHEET có giúp ích cho doanh nghiệp của bạn hay không? [ DONATE ] |
Alldatasheet là | Quảng cáo | Liên lạc với chúng tôi | Chính sách bảo mật | Liên kết đến bảng dữ liệu | Trao đổi link | Tìm kiếm theo nhà sản xuất All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |